No Signal on New Nfusion HD

[bchaudry]

Hello:
I'm a new member to this forum and could really use some help.

I currently have an Nfusion Solaris and decided to upgrade to the HD...I assumed that since the Solaris works with no issues that I simply had to replace the solaris with my new HD receiver without having to adjust/change my hardware setup (Dishnetwork 500 pointing at 110, 118 &119). I used the same antenna settings in the HD as I have with the Solaris but no luck. I have also updated the HD with the latest BIN file which I installed via USB. Any help would be greatly appreciated!

Thanks in advance

[Blankstare]

Originally Posted by bchaudry

Hello:
I'm a new member to this forum and could really use some help.

I currently have an Nfusion Solaris and decided to upgrade to the HD...I assumed that since the Solaris works with no issues that I simply had to replace the solaris with my new HD receiver without having to adjust/change my hardware setup (Dishnetwork 500 pointing at 110, 118 &119). I used the same antenna settings in the HD as I have with the Solaris but no luck. I have also updated the HD with the latest BIN file which I installed via USB. Any help would be greatly appreciated!

Thanks in advance

110 118.8 & 119 is the d500+ What are your antenna settings?

Default LNB type setting is set Standard, change to DPLNBF
11250
119 Port 1 DiSEqC 1.0
110 Port 2 DiSEqC 1.0
118.8 Port 3 DiSEqC 1.0

[shery20]

do you have jumper cable connected to 8psk module

[johnnybluedawg]

are you getting an IP Address on ur HD ? what happens when u go into ur network settings ?

[bchaudry]

Originally Posted by johnnybluedawg

are you getting an IP Address on ur HD ? what happens when u go into ur network settings ?

Yes, I am able to get a valid IP address.

Originally Posted by Blankstare

110 118.8 & 119 is the d500+ What are your antenna settings?

Default LNB type setting is set Standard, change to DPLNBF
11250
119 Port 1 DiSEqC 1.0
110 Port 2 DiSEqC 1.0
118.8 Port 3 DiSEqC 1.0

I tried using what you mentioned above but was not able to get signal.

Originally Posted by shery20

do you have jumper cable connected to 8psk module

I took this off-I wasnt sure what it was for...i don't have the jumper with me so I wont be able to troubleshoot to see if that's the issue. Could this be why?

FYI... for Sat 119 I chose:
LNB Type: DPLNBF
22KHz: OFF
LNB Power: ON
DiSEqC mode: 1.0
DiSEqC Option: Port 1
Legacy SW: Disable
TP List: 1.12224

[snakebite]

you need the jumper cable hooked up my friend to get a signal ,i take it you bought it with module?

[bchaudry]

One more thing to mention is that I do not have a DiSEqC switch connected. I figured since I'm not using one with the Solairs that I don't need one for the HD. Is that correct?

[snakebite]

with the lnb you have i believe it has a built in switch.

[bchaudry]

Originally Posted by snakebite

you need the jumper cable hooked up my friend to get a signal ,i take it you bought it with module?

Yes, it came loaded with the 8psk module... I don't what I was thinking when I took the cable off...I'll go to the store to pick up a cable to see if that works. BTW I dont recall where it needs to be connected, could you please advise?

[snakebite]

you need to connect it to the if out to the uhf remote.

[shery20]

please watch this video at the end of this video it will show you where to connect the cable http://www.abadss.com/forum/1005-nfu...hd-unit.htmlre is the link

[bchaudry]

you were right Snake, hooking up the jumper allowed me to catch signals. I was able to scan and get all the channels but now the issue is, I'm getting the service not available message? Any ideas?

[bchaudry]

BTW the using v1.3sr 25F

[bchaudry]

i was able to get picture after reading a few other posts by turning the proxy and emul off... prob now is the picture keeps freezing, but it looks like others are having this same problem as well.

Thanks everyone for all the help!