No signal on Nfusion HD

[rzarectah01]

Hello, this is my 1st post. I recently hooked up my nfusion hd receiver and I had signal before I updated the factory file and bin file. Now after I updated through the null cable my signal stays at 18 strength, even if there is no wire in the back of the receiver going to the LB IN input. Please help as this is my 1st FTA receiver and I am clueless as to why I cant get signal anymore. The dish is in the same place it was when I was receiving signal. I have the 1000.1 turbo hd dish.

[snakebite]

do you have little jumper cable hooked up to the uhf remote to if out?

[rzarectah01]

Originally Posted by snakebite

do you have little jumper cable hooked up to the uhf remote to if out?

I do not know what you mean by jumper cable? My remote seems to be working fine?

[rzarectah01]

Originally Posted by rzarectah01

I do not know what you mean by jumper cable? My remote seems to be working fine?

I had a professional come in and install the dish, if that helps

[snakebite]

on your reciever when you bought it did you get it with HD module? if you got the module ,on the back of your reciever you should have a little jumper cable that plugs into-it says on the back-uhf remote to the if out ,it is for your hd module to send signal.

[rzarectah01]

I did get the module installed when I got the receiver. There is a place to put a coaxle wire it says uhf remote antenna. I also see the if out input. Are you saying I need a wire going from the uhf input into the IF input on the back of the receiver?

[bat01]

Originally Posted by rzarectah01

I did get the module installed when I got the receiver. There is a place to put a coaxle wire it says uhf remote antenna. I also see the if out input. Are you saying I need a wire going from the uhf input into the IF input on the back of the receiver?

No jumper with module means no signal.

[snakebite]

yes you need that cable hooked up.

[rzarectah01]

I ran a coaxle from the UHF remote to the IF output and I have great signal now on the left signal bar but on the right bar i have 0. My receiver also defaults to 148 lnb when I exit out of the menu and I still see no (or bad signal) come up on my screen. We are almost there!! Please help

[snakebite]

Identifying Marks
-----------------
Uniquely shaped LNB
DishPro Plus markings
3 coax connector outputs and one coax input.

Usage
-----
These are used to provide signal from 3 (or 4) satellites to up to 3 receivers (specifically 129/119/110).
Using DPP44 switches you can feed many more receivers. When using DPP44s the input port is disabled and you will need to connect the LNB directly to the DPP44.
DishPro Plus (DPP) LNBs are power hogs and some FTA receivers may have trouble powering it by themselves without power inserters or a sub box hooked up too.

Antenna Settings
----------------
LNB Type: Single DPLNBF
LO_freq: 11250
Sat 1: DiSEqC 1.0 Port 1
Sat 2: DiSEqC 1.0 Port 2
Sat 3: DiSEqC 1.0 Port 3
Sat 4 (input port): DiSEqC 1.0 Port 4

[rzarectah01]

the installer hooked it up for 110 119 and 129. I now great signal on both bars but when i input what you said above, lnb- dplnbf diseqc mode- diseqc 1.0 (dp21, 34)
diseqc option - port 1

then when i exit it seems to default back to 148w 12516/v/20000 and says service not available?

[rzarectah01]

I figured out how to switch from diff lnbs. Now I have it on 110 and I get this message on all the channels. in/nn/pn Emuln/ S.U.N.S. disconnected?

[snakebite]

you need to go into antenna settings and do each sat 1 at a time and assign the proper ports to each seperate sat ,then when you hit the red f1 to scan it should save that 1 sat setting ,then when thats done do second sat and set up the same but assign it to port 2 .and so on

LNB Type: Single DPLNBF
LO_freq: 11250
Sat 1: Diseqc 1.0 Port 1-119

Sat 2: Diseqc 1.0 Port 2-110

Sat 3: Diseqc 1.0 Port 3-129

[snakebite]

you need to go into your network settings and turn proxy off(p-on)should be off,then in user settings tun emul off.

[rzarectah01]

I have saved and scanned all lnbs to diff ports. Still getting the errors above and cannot see any channels.

[snakebite]

your on screen message should read i-on-n-on-p-off-emul -off ,use the directions i gave you in post 14 and you will get picture.

[rzarectah01]

It works, thanks so much!!!! Which lnbs have most of the hd channels. Again thanks!!!!

[snakebite]

right now 129 is HD but there isnt alot up yet but supposedly its comming .82w has the most HD channels up but it is hard to get if at all if your not in canada.glad to hear your up and running ,write down your settings so you have something to fall back on if you have to rescan or something happens.

[rzarectah01]

Will do thanks, Not all the channels have the guide feature is this normal?

[snakebite]

do you have guide set for epg -3days and your time set correct and summertime off.