Lothario_V201_PUFF_Pansat/Fortec

[Takoda]

I noticed this bin posted to another site first before it got here and saw people having issues with it but when it popped up here on aba I thought for sure it would have been checked out. So I installed it and I got the same problem everyone else has: P U F F keeps scrolling across the panel after you load the bin, it reboots, and then you power off to move back to TV and turn it back on. PUFF just keeps scrolling away. Do I need to try reloading it a few times or what? I was leery of installing anything other than a JVVH or team Puff file to begin with so I may just wait to see if Team Puff will release BIN 300.

[tomcat01]

i am going to wait o have 2 boxes i read the same thing .. i am going to wait for the other puff and one b-75 and test both .., 2 boxes read to flash .. ..

i have a jtag so if i kill them not a big deal ..

[fools gold]

laughs, same here, but like post like this , will get it fixed,

[60'sDude]

Just for the sake of doing something with the TV Today, I tries this BIN in a Fortec Lifetime Ultra.... DON'T BOTHER... When the P U F F P U F F finally froze on F for about 45 seconds, The display went to -75 then is went to ON... Then back to P U F F P U F F (the PUFF version of nightrider???) THIS BIN NEEDS ALOT MORE WORK!!! OR TOSSED OUT!!!

[fools gold]

agree, but nobody is perfic, laughs, see what i mean, fixes will work, it just takes time, like i did , read a book, if your mind is like mine, u can go anywhere,

[wildbill1963]

I found this info and not sure if it works or not:

"The new 201 bin file will not work if you use your old channels. I have tried and comfirmed this. Also it can cause Echo 8.10/Ku to show no signal. Could be why 61.5W is not working, too. Factory Reset first. Reload the bin and keep the receiver powered On and manually set the satellites back up, then blind scan the channels in one satellite at a time.

Blind scans are the recommended scan for these receivers.

Write down all your antenna settings before you do a Factory Reset and always keep your settings in a safe place. Some tuck them in their manual.

Setup satellites, Exit, Ok to Save on each one.

Go down to blind scan, and do each one once, seperately.

This file is working, and later releases may do the same thing."

[fools gold]

hmm, but we have to be able to get in to the menu to do that. ?????

[tomcat01]

three is the way you are saying but do you guys really want to take the chance of killing your reciever for me i know how to jtag and get it back but for the most alot of users do not so i am just trying to protect members here ..

there will be another few puff files coming out just have to wait i say until tomorrow .. .. better safe than sorry ..

[fools gold]

i agree, too, like i said, a good book will work right now,,

[Oscarn]

eso quiere decir que este bin no funciona? para 2700A
X-87BL_081207_B75_V201_api_femu.rar
y que se puede hacer aparte de eso
saludos y gracias

[matohota1992]

Originally Posted by Takoda

I noticed this bin posted to another site first before it got here and saw people having issues with it but when it popped up here on aba I thought for sure it would have been checked out. So I installed it and I got the same problem everyone else has: P U F F keeps scrolling across the panel after you load the bin, it reboots, and then you power off to move back to TV and turn it back on. PUFF just keeps scrolling away. Do I need to try reloading it a few times or what? I was leery of installing anything other than a JVVH or team Puff file to begin with so I may just wait to see if Team Puff will release BIN 300.

Jvvh_Fortec-Pansat_260_(PUFF)(Recovery) wiil fix to we have new bin

[tomcat01]

here people have sucess doing it this way

201 does not like the 2nd reboot so do not allow your receiver to reboot twice.

If you have to load the bin from a computer at another location, simply Power OFF the receiver right after it finished loading the bin.

Now take the receiver back to where it was, connect all cables and Power UP. Everything should work as it should now.

If you have a PUFF-PUFF loop, simply reload 201, no need to load old bins.

Do not Power OFF the receiver until next bin!

[jetta839]

Originally Posted by Oscarn

eso quiere decir que este bin no funciona? para 2700A
X-87BL_081207_B75_V201_api_femu.rar
y que se puede hacer aparte de eso
saludos y gracias

Aparentemente no funciona, solo hay que esperar un próximo bin que funcione...paciencia....

[wildbill1963]

New Bin File Pansat 201 Full EMU - Problems Solved 2700A 2700E 2700 2500A 2500

Problem: Receiver keeps rebooting. (2700A)
You cannot shut it OFF once the new file is installed.
To cure this, write an older file (i.e 2.98 or 2.99)
Or write the 201 file again and DO NOT turn the receiver power OFF.

Problem: Rolling PUFF on display. (2500A)
You cannot turn the power OFF once the file is loaded.
To cure this, write an older file (i.e 2.98 or 2.99) PUFF rolling will stop.
Or write the 201 file again and DO NOT turn the receiver power OFF.

Problem: Scrambled or Bad Channel error. (2500A or 2700A)
You will need to Factory Reset and resetup and rescan channels.

Problem: No Signal error. (2500A or 2700A)
You will need to Factory Reset and resetup and rescan channels.


Blind Scan Instructions

The new 201 Full EMU bin file will not work if you use your old channels. I have tried and comfirmed this. Also it can cause Echo 8.10/Ku to show no signal. If you think the file is bad, change satellites and you will find out it does work. This could explain why 61.5W is not working, too, and others. Factory Reset first. Reload the bin and keep the receiver powered On and manually set the satellites back up, then blind scan the channels in one satellite at a time.

Blind Scans are the recommended scan method for these receivers.

Write down all your antenna settings before you do a Factory Reset and always keep your settings in a safe place. Some tuck the paper they are written on in their User Manual.

Setup each satellite, Exit, Ok to Save on each one.

Notes:
To see Quality on Echo 6.8/Ku or 8.10/Ku (same satellite) default TP [1] 12224 V 20.000
To see Quality on Echo 7/Ku change the TP to [2] 12239 V 20.000 (119W)
To see Quality on Echo 3/Ku change the TP to [6] 12297 V 20.000 or [8] 12236 V 20.000 (61.5W)
To see Quality on Echo 5/Ku change the TP to [5] 12282 V 20.000 (129W)

Go down to blind scan, and blind scan each satellite once, seperately.

This file is working, and all later releases will probably do the same thing until you do this resetup and rescan procedure. A later file release will cure the problem with turning it Off. Try a long extension cord if your computer is too far from your TV, temporarily. Or, hope you have a friend with a Laptop with a serial port or a USB To Serial Adapter.

Other settings, set your Time Zone to your area. Summer Time OFF.

Renumber Local CH, enter City / State and Save.

Hit the SAT button and select Echostar Package. A box will pop up, select any channel there. This will place all channels in the proper provider order.

You should be good to go now.

Hope This All Helps For Now !!

[basscat02]

Guys, listen to TC on this. He knows what he is doing and he is trying to protect you guys from frying your receivers.

[WarezMonkey]

I been a long time reader of the site, I never taken time to post before but thought I may be able to give a little back to the community.

I have a fortec Lifetime ultra converted to puff v1.0. I installed the Fwank7 Jvvh-Team-PUFF V201 then I installed my channel list that I been using for many of the past bins. When I went to use the receiver I ran into the very same problem as stated with puff puff scrolling in a loop.

After reading this post I decided to reinstall The 201 bin but not my channel list. I shut the receivers power button off on the back when the bin reload was completed.

Then I unplugged the unit took it to my tv and plugged it in and turned on the unit, it took about 45 secs to come back on, to my surprise I saw the epg loading screen and there was all my saved channels.

I am not sure how they stayed after the bin reload but they did and the units working. Maybe someone can confirm this and save some others the hassle of a rescan.

[carlos60]

New Files Tested and Work Fine
Go here http://www.abadss.com/forum/187-fort...tml#post541504

[deathnote]

file works fine reload it wait for it to say complete turn your reciver off hook satalite cable in turn back on and your through
use your remote to turn it on and off not back switch

[rr52]

I'll wait.

[tomcat01]

closed guys i am going to paste a how to in the file section under carloses release for the jvvh file