2700A quality problem

[REDLIDER]

Hello, i got a problem of not signal on 2700 a,

i put a diferent reciber coolsat and they recibe the ppv on dish 110 only by conecting the antena, so i supost that the antena is fine oriented,since the coolsat the level is 99 % and the quality is 85 %,

but when i put my pansat 2700a i got no signal.
99 % level
0% quality

i already put the bit 214 and 218 but still quality say 0 % can some 1 help me please tnx.

[boboisno1]

Did you use the same antenna settings in the pansat as the ones in the coolsat? I.E lnb type, lnb freq etc?

[REDLIDER]

Originally Posted by boboisno1

Did you use the same antenna settings in the pansat as the ones in the coolsat? I.E lnb type, lnb freq etc?

yes, i use the echo8 seathing by default factory seting on the 2 reciber and are the same, also i try to change the frecuency and still no bar up.

[boboisno1]

LNB freq is 11250. are the ports set up exactly the same in the pan as the cs i.e port none or 119 port 1 110 port 2 lnb type standard or ocs tc?

[REDLIDER]

Originally Posted by boboisno1

LNB freq is 11250. are the ports set up exactly the same in the pan as the cs i.e port none or 119 port 1 110 port 2 lnb type standard or ocs tc?

tnx..


i got this this setup

lnb type standar
;nb local freq. 11250
22 khtz off
diseqc off
legacy sw none
skew 45
tp ( 7 ) 12326

[boboisno1]

Since you have a skew I would assume you're pointing to more than 1 sat, you would then likely need to have a port selected. What type of dish and lnb do you have?

[REDLIDER]

i got a antena of directv by phillips and the lnb is only 1 lnb ball whit 2 conectors for coaxial cable it say compatible whit direct tv multi -satelite
950-1450 mhz.

and about the skew i never move it since the default reciber was programed. and i only use 1 sat.

i never toucht or change the skew seting sinc ei buy it the # was there when i buyit and was work it whit that config.

[boboisno1]

I'm at loss if you have used the exact same antenna settings in the pansat as the coolsat. I can tell you that dish isn't the best to use, it should get you one sat, for 110 use trans 12224.

[REDLIDER]

i dont have that frec. 12224. i only got 12223 and then the next selection is 12226 frec.

[boboisno1]

What are you picking for the sat echo 8/10?

[REDLIDER]

dish 500 on coolsat and long time ago about 6 monts on my pansat the same, and since 6 months ago when my last screen say badchanel o scramble signal was display y put the recyber on a box, yesterday i intal the new bins, but i found that i dont have quality my broo, bring to my home is reciber and put is reciber to my antena sinc ei was think was moved by the air, but not the reciber get signal and we can view the ppv.

so i bring my reciber to my broo home he plug is reciber to antena nad they have signal and quality and i plug my pansat and dont have quiality.

well i give it up for now, since i dont know what to make, my reciber is almost new and was workinf very good until the last bin arund 6 monts. and afther scramble screen i put on the box.

[boboisno1]

If you have the dish 500 try these antenna settings.

Echo 7 119W
LNB Power: On
LNB Type: OCS-DP
LNB Freq: 11250
22KHz: Off
TP: 12239
DiSEqC: Port 1
Motor: Off
Legacy SW: None

Echo 8 110W
LNB Power: On
LNB Type: OCS-DP
LNB Freq: 11250
22KHz: Off
TP: 12224
DiSEqC: Port 2
Motor: Off
Legacy SW: None

[REDLIDER]

do you think that can be fixed if i put the factory bin ? and the the bin75 again ?

[boboisno1]

It may fix it, at this point it probably can't hurt to try.

[Victor Hugo]

You are right factory settings that clean the box , of the many information she has.
Let US know what happen? Because that is the way we learn OK?