trying to jtag a dead pansat

[hunter50]

I just got my jtag and looking to try to jtag it and have tv again but i see the posts from arbor and grasshopper on how to but im still a bit confused.
1. the cable only plugs in at one port ? it has 2 and 2 small pin plugs
need some help with the set up.
thanks

[hunter50]

im looking for the wall loader i think but unable to open it

[bel71281]

all files and instructions are included here. http://www.abadss.com/forum/15-pansa...html#post56504 have downloaded and open all these files.

[hunter50]

Originally Posted by bel71281

all files and instructions are included here. http://www.abadss.com/forum/15-pansa...html#post56504 have downloaded and open all these files.

thanks buddy but im not being allowed to open the wall file that is in arbors and grasshoppers how to posts i see all the directions but i cant open the files that they say ... not sure why
thanks

[boboisno1]

I uploaded a complete guide with pics etc, I'm not sure if it's all here already or not, it's waiting approval.

Originally Posted by hunter50

thanks buddy but im not being allowed to open the wall file that is in arbors and grasshoppers how to posts i see all the directions but i cant open the files that they say ... not sure why
thanks

[boboisno1]

Here's the instructions it has about the wall.

The program is pretty self-explanatory.

The programming start address is calculated as the Base Address + Offset.
The programmer assumes that all input files have been recorded with offset 0.
When programming the file is read starting at the offset byte.

Backup Flash:

U22:
1. Select Flash Base Address -> 1FC00000
2. Select Length -> 200000
3. Select Offset -> 0
4. Select Action->Read Flash
5. Enter the file you want to save in.
U23:
1. Select Flash Base Address -> 1FE00000
2. Select Length -> 1F0000
3. Select Offset -> 0
4. Select Action->Read Flash
5. Enter the file you want to save in.

Erase Flash:

1. Select the Flash address that you want to erase.
2. Select Action->Erase Flash

Program Flash:

1. Hit Select Button to Select the input file.
2. Make sure base address and length are correct.
3. Offset should be set to where in the flash, relative to the beginning, that you want to start programming at.
This is 0 when doing an entire flash program.
4. Make sure that the serial number and boxkey is correct.
To read the current boxkey and serial number from the flash, hit the refresh button.
5. Select Action->Program Flash

Erase Sector:
1. Select the Base Address of the flash you want to erase the sector in.
2. Enter the offset where the sector is.
ie to erase sector at 0x1FC60000, Select base address 1FC00000, offset 60000
3. Select Action->Erase Sector

New in Version 2.1:

JTAG Delay : This is the delay between the cycling of of the clock. Higher settings may work better but will slow down programming. Try values like 100, 1000, etc.

Slow Mode : Setting this will cause Wall to use only the slow method of accessing the flash. Try setting this if you are having problems.

Fixed asymetrical clock in version 2.2

[hunter50]

Originally Posted by boboisno1

I uploaded a complete guide with pics etc, I'm not sure if it's all here already or not, it's waiting approval.

thanks alot buddy it is greatly appreciated
im guessing you have tagged a 3500??

[boboisno1]

Here is the link. I've never done one but I always keep info handy on my computer, you never know when you might need it.

http://www.abadss.com/forum/164-pans...tructions.html

[hunter50]

Hey bobo im looking in the how to posts and directions and trying to open the wall to run but it keeps comine failed and unable to open.....