can anyone help me plzzzzzzzzzzzzzzzz

[zainnumberone]

hi! i need help i accidently did factory default and don't remember my installiation set-up. + i can't get the stb in boot mode. Plzzz someone help me
Thanks to all for the help.

[jc7257]

Originally Posted by zainnumberone

hi! i need help i accidently did factory default and don't remember my installiation set-up. + i can't get the stb in boot mode. Plzzz someone help me
Thanks to all for the help.

You don't need it in boot mode. All you did was erase your sat settings, not the bin. Just enter the sat settings for the sat and network you are after...

[zekester]

Originally Posted by zainnumberone

hi! i need help i accidently did factory default and don't remember my installiation set-up. + i can't get the stb in boot mode. Plzzz someone help me
Thanks to all for the help.

If you can't remember what settings to put in, post back and let us know the sats you're trying to get and the LNB's used, switch if any etc.

[zainnumberone]

i am trying to get 61.5 110 n 119 with the supplies switch from CW-600s

[zekester]

Standard settings for 110 and 119. I don't get 61.5 but I'm sure someone will post them
lnb type standard (if DP LNB choose OCS-dp)
lnb freq 11250
22khz off
TP frequency 12224 for 110 and 12239 for 119
diseqc select correct port (for switch as posted above)
Motort Off
Legacy sw none

When done rescan for channels. And let it roll.

[zainnumberone]

i tried those do i do blind or auto sacn

[zainnumberone]

it doesn't get me all the channels and no channels from 110 what so ever

[Bud_Alcor]

Originally Posted by zainnumberone

i tried those do i do blind or auto sacn

Do auto scan, blind scan mulitple the channels.

[zainnumberone]

should i delete all the channels b/c autoscan creates more multiples

[zekester]

Don't have Blind scan on mine see Bud's post above.

[zainnumberone]

when i try the settings it shows 60-75 signal but no quality.

[zainnumberone]

i am trying to get science and discove channel

[zainnumberone]

my current settings are
110
tp 12224/V/20000/Auto
Lnb freq. 11250
type Normal
22 off
disqec Lnb1
legacy off
Signal 69% no Quality

119
tp 12282/V/20000/Auto
lnb freq 11250
lnb type norm
22 off

disqc lnb3
legacy off
signal 75% and Q 89%

[bel71281]

what kind of dish do u have and are u going through a diseq switch. lnb type is important here.

[Bud_Alcor]

We need the lnb type . Does it says Dish Pro???

[zainnumberone]

no not dishpro just the old one i don't remeber and is going through switch supplied by CW

[bel71281]

look at the diseq switch and see which ports have cables going to them and which sat. why do u have port 3 on 119? is that the port you have the cable going to? switch them around and put 119 on port 1 and 110 on port 2.


your settings should look something like this

Satellite..............EchoStar 8,10 (110W)
LNB Power .............ON
LNB Type...............Standard (For Dish Pro set to OCS)
LNB Freq...............11250
22KHz..................OFF
TP Freq................12224
DiESqC 1.0.............Port 2
Motor..................OFF
Legacy SW..............None


Satellite..............Echostar 7 (119W)
LNB power..............ON
LNB Type...............Standard (For Dish Pro set to OCS)
LNB Freq...............11250
22KHz..................OFF
TP Freq................12239
DiESqC 1.0.............Port 1
Motor..................OFF
Legacy SW..............None

[zainnumberone]

is there an other way to check the switch cause there is ice on the roof and can't go up there untill it melts

[zainnumberone]

the rx keeps on going into this mode wat should i do --:--

[zainnumberone]

i also have 61.5 connected as well