Help NoCh

[jt.8889]

Hello i got this messege on my viewsat vs 2000 and i dont know what to do i want to get my chanels back but i dont know anything about it!!! please help !

[Laser2008]

you need to set up your sats and do a auto scan again...
Set Satellite to the desired satellite.
Set LNB Power to On.
Set LNB Type. Legacy Single and Dual LNB's should be set to Standard.
Legacy Twin and Quad LNB's have their own dedicated types (LNB1 = higher azimuth satellite / LNB2 = lower azimuth satellite). Dish Pro LNB's should be set to OCS-DP.
Set LNB Freq. to 11250.
Set 22 KHz. Select Off or On, as appropriate, if a 22 KHz switch is used with this LNB. Otherwise, select Off is no 22 KHz switch is used with this LNB.
Set TP Freq. to 12224 unless this satellite is EchoStar 7 (119.0W), in which case use 12239 instead. The TP Freq. setting is not saved upon exit. This is normal and will not affect any subsequent operations.
Set DiSEqC 1.0. If an external DiSEqC switch is being used with this LNB, select the appropriate port number. If this LNB is a DishPro Twin or Quad, select port 1 (higher azimuth satellite) or port 2 (lower azimuth satellite), as appropriate. Otherwise, select None if no DiSEqC switch is used with this LNB.
Set Motor as required for your installation. If no motor is used, set Motor to Off.
Set Legacy SW. If this LNB is a Legacy Twin or Quad, select SW42 Dish 1 (higher azimuth satellite) or SW42 Dish 2 (lower azimuth satellite), as appropriate. If using an external Legacy Switch with this LNB, select the appropriate type.
At this point, you should see readings on the signal strength (S) and quality (Q) meters above 50.

You should also see the expected satellite name displayed in the upper right corner of the screen, superimposed on the blue bar to the right of the words "Antenna Setup", and it must match the satellite name to right of the 'Satellite' label in the menu.

If you don't see the proper satellite name displayed or don't have reasonable signal readings, you should not proceed. You may need to reposition your antenna or correct wiring problems.

Repeat the Antenna Setup procedure, as needed, for each additional satellite.

When finished configuring satellites, press Exit and press OK with Yes selected to save your settings.


Select Installation -> Auto Scan. Set Search option to All and Network Search to On. If you are configured for multiple satellites, press F1, place a check-mark after all configured satellite names, then press Exit.
Select Scan Start and press OK.
When scanning has completed, press OK with Yes selected to save the results.

[chicoluv]

Originally Posted by jt.8889

Hello i got this messege on my viewsat vs 2000 and i dont know what to do i want to get my chanels back but i dont know anything about it!!! please help !

Hello Jt ,Did u try a hardboot ( rear-switch) ? Then put on ch#200 a wait .

OK ,sorry laser . u mite have the right idea .

[cdo_care]

Originally Posted by jt.8889

Hello i got this messege on my viewsat vs 2000 and i dont know what to do i want to get my chanels back but i dont know anything about it!!! please help !

first of all to ABAdss. Buddy just do antenna setting then autoscan the Sat.

[jt.8889]

i did what you rold me but i dont have all my chanels ... i live in the west coast i dont know if the settings are different but i only get a little bit of chanels...?

[boboisno1]

My current antenna settings are
for the Echostar 8 10
LNB = on
LNB type = standard OCS if you have a dish 500
LNB Freq = 11250
22khz = on Off
tp freq = 12253 use 12224
diseq= port4 Make sure you have the sat for 110 actually plugged into port 4
motor= installer turn to off
legacy SW = none

and for Echostar 7 i have
LNB= on
LNB type = standard OCS if you have a dish 500
LNB freq =11250
22khz = on Off
tp freq= 12224 Use 12239
diseqc = port 2 Make sure you have the sat for 119 actually plugged into port 2
motor = off
legasy= none

[wheeler18]

I tried resetting the satellite and it still shows noch on my receiver and nor tv channels on the television.