Question??

[briansd]

i have dl the latest file and it worked for a while now a lot of the channels are saying a/r is it just me or is everybody having this problem. it just started doing this about 3 days ago. the latest file d/l was the 080627 fix.

[spyder123]

i think it's just you.
have you tried a hard boot lately?

[just4ufolks]

Ensure ur auto roll n auto TP are ON..??
Reboot from the back switch n leave it on on 200 or 150 ..sud b gud 2b back..??
Unplug from power source n restart after a few minutes like 2-3 minutes..
If need be RESCAN (AUTO SCAN) the reciever n go from there..
Keep the forum posted n is need that extra help just ask...n post back with with ur reciever settings ..

[briansd]

yes i already tried a hard boot and my settings are on echo 8,10 are
lnb- on
lnb type- ocs-dp
freq- 11250
22khz- off
tp- 12253
port- 2
off
none

and echo 7 is
lnb- on
type- ocs-dp
freq- 11250
22khz- off
tp- 12239
port- 1
off
none

i can go to a channel and it will say a/r i can go past some of them by going up of down about 5 or 6 channels and then go back and sometimes it works and the channel comes in and some of them still say a/r

[spyder123]

LNB type- ocs-dp
freq- 11250
22khz- off
tp- 12253 <---- try changing to 12224
port- 2
off
none

[briansd]

that still didnt work it still does it on some channels

[briansd]

i can go up or down a few channels and then back to the channel and it sometimes works i dont understand what is causing the problem

[just4ufolks]

Did you check the if the auto rill n auto TP are set to relevent correct settings??

Leave at 150 or 200 for a short time..??

AUTO SCAN..?

If all fails to revive n get the missing channels back??
Here is the link to get back to working...install current working file again as well...

http://www.abadss.com/forum/173-view...gin-files.html

Gud Luk..look fwd 2ur feedback..

[Beefeater1]

Originally Posted by briansd

i can go up or down a few channels and then back to the channel and it sometimes works i dont understand what is causing the problem

I would probably do a factory default and then start from scratch making sure these setting are perfect and good q/s on both sats.


Antenna setup:
Satellite........................echostar 8,10
LNB power......................on
LNB type........................OSC_Dp lnb -
LNB freq........................11250
22khz...........................off
TP freq.........................12224< spot beam
seach option.................all
disqec 1.0.....................port 2
motor...........................off
legacy SW.....................none< or port 2

F1 to scan then save

Antenna setup:
Satellite.........................echostar 7
LNB power.......................on
LNB type.........................OCS_Dp< w/Dp lnb
LNB freq..........................11250
22 khz...........................off
TP freq..........................12239<spot beam
search option..................all
Diseqc 1.0......................port 1
motor............................off
legacy sw......................none< or port 1

[forrestgump]

I have the same problem with one of mine and I'm too lazy to read and get enough info to fix it. A lazy fix is to turn off the reciever off with the remote and turn it right back on. Mine always come back on on echo 8, 10 so if I'm watching something on echo 7 and want to watch something on 8, 10 I just turn it off with the remote and like magic it comes back on on 8, 10. This is not a way to fix your problem, only a lazy man's way to work around it.

[taz73]

what type of lnb do you have. I know that mine had to be on standard to work properly. if this doesn't work check dish location and cables again then try once more scanning the sats seperately.