PLEASE DO NOT PM ME WITH QUESTIONS, POST THEM IN A NEW THREAD.
YOU CAN PRINT THIS OUT
Go close to the top of this thread and click on THREAD TOOLS then click SHOW PRINTABLE VERSION then click PRINT in your browser. I am not taking credit for this bin only the instructions.
DBPSW-070125XTREAM.zip you can get it here
http://www.abadss.com/forum/viewsat-extreme/15001-xtreme-release-dbpsw-070125x-jan-26-2007-a.html
LOADER2.ZIP You can get it here.
http://www.abadss.com/forum/viewsat-general-downloads/5677-loader2-viewsat.html
A Satellite List for all the KU Satellites. You can get it here if you want it.
To unzip the files you can use WinZip or Winace. You can get them here h**p://www.winzip.com/ or h**p://www.winace.com/ Winace will unzip a rar file also.
KeyGrabber you can get it here
http://www.abadss.com/forum/keys-discussion/13287-key-grabber.html
KeyMaster you can get it here
http://www.abadss.com/forum/keys-discussion/14272-key-master-3-0-a.html
HOW TO FLASH.
You can flash (load) your receiver with a bin on top of the bin (file) you already have. It will replace it.
Use a Null CABLE RS232 on your receiver from the computer. Or use a Null adaptor from Radio Shack number 26-264B to make a straight through cable a Null cable. Take the cable off going to the LNB to be safe. If you don't have a 9 pin plug on your computer you may need to use a USB to Serial cable 26-183 at Radio Shack with a Null adaptor. If you need a 9 pin mail to mail gender adapter it is item #: 26-231. You will need to install a drive in your computer for the USB cable.
Un-zip all the files and hook up the cable from your computer to the STB, keep the STB off with the switch in the back. Start the loader-2 and click on OPEN FILES. Find the bin file you un-zipped that now ends in PGM. Click on it and it will automatically go on the first line of the loader. Click on the icon just below the word TOOL and check the COM PORT. Then turn STB on from the back and at first light click PC->STB on the loader. If the progress bar don't move after about a minute start over again. Sometimes the timing is critical. Even try turning STB on from the back first then click PC->STB. Don't do anything as the progress bar is going across. Make sure the Computer & STB are done before you go to the next step. They may not get done at the same time. The receiver needs up to one minute to process the data, (DON'T RUSH THIS).
You may need to put a list of Satellites in your STB if you don't have any. Click on OPEN FILES and find the Satellite list you already downloaded and un-zipped. Now do the same thing you did above to flash your STB.
PLUGGING IN CABLE.
Make sure you plug in the cable from the dish to the receiver at the LNB 13/18v INPUT. Not the ANT IN. The cables coming from the dish to the switch should be put on the switch at the same number as you have set in your receiver. "Example", 119 cable goes on number 1 on the diseqc switch and the receiver has #1 for 119 in the program. You can only get one Satellite for each one LNB you have. Two LNB's two Satellites, and so on.
Now you should set your settings. Below is what most have.
MENU, INSTALLATION, then 0000 or 0937 or 2668 or 3570 then ANTENNA SETUP then side arrow to ECHOSTAR 7 119.0W. Then do the same to ECHOSTAR 8,10 110.0W
----EchoStar 7 119.-----EchoStar 8,10 - 110.0W
LNB Power------ON-------------------ON
LNB Type-----Standard-----------Standard Dish Pro change to OCS-DP
LNB Freq---------11250-------------11250
22kHz-------------ON--------- -------Off If you don't have a 22kHz switch both can be off. A DP34 don't work well.
TP Freq----------12224--------------12224 Or one that is close. This TP is just a starting point.
Search option-----All----------------- All
DiSEqC 1.0------Port 1--------------Port 2 This should match the cables on the switch.
Motor-------------Off----------------Off
Legacy SW------None---------------None
This is with the above two
Satellite: any other
LNB Power-------ON
LNB Type-----Standard Dish Pro change to OCS-DP
LNB Freq--------11250
22kHz-------------OFF you can't use a 22kHz switch with more then two Satellites. A DP34 don't work well.
TP Freq----------12224 Or one that is close. This TP is just a starting point.
Search option-----All
DiSEqC 1.0------Port 3 This should match the cables on the switch.
Motor-------------Off
Legacy SW------None
THIS IS WHAT MOST SETTINGS ARE. You can start here then change them later.
MENU, OPTIONS
Close Caption---------OFF
Sort by SID------------ON
AUTO TP--------------ON
AUTO ROLL------------ON
EPG Hours-------------12
Full Channel Name-----ON
Installation, Parental Control
Receiver lock------------Off
Menu Lock---------------ON
Information timeout-------3
Maturity Rate-------Unblocked
Change PIN Code--------????
MENU, SYSTEM SETTINGS
System Settings----Letter Box
Screen Type-----------63
Menu Language-------English
Audio Language---- --English
Channel Mode---------Normal
HOW TO DO A FACTORY DEFAULT
MENU, INSTALLATION
When you do this you will also clean out your channels.
HOW TO SCAN A SATELLITE FOR CHANNELS
You should scan for the channels. Sometimes when you use a channel list the keys or TP auto-roll will not work.
MENU, INSTALLATION, ANTENNA SETUP, then side arrow to Satellite to be scanned. then
The bottom of the screen will tell you to click on F1 or F2 key on the remote to start the scan.
HOW TO ENTER KEYS MANUALLY
In the setup under CODE (the keys) you will find DISH in two places, 00 01 00 and 01 01 00. Change the keys in 01 01 00. The "F' key may be the COLOR button on remote's if you don't have the TEXT button.
1 Menu, 2 Installation, 3 Enter Pin 0000, 4 Code, 5 Nagra, 6 Left until you see Dish or whatever.
Put 00 keys on line 08 & 09 don't change the 08 or 09 number
Put 01 keys on line 88 & 89 don't change the 88 or 89 number
EXIT once then OK to save, the light color is the one you pick to save then EXIT out.
HOW TO SEARCH/EDIT, ANTENNA CONFIGURATION, ADD SATELLITE, RENAME SATELLITE, DELETE SATELLITE.
MENU, INSTALLATION, 0000, SIDE ARROW TO DN OR whatever, then down once to NETWORK SEARCH ON, Then down once to HAMMER ICON then side arrow to what you want to do.
CHANNEL NAME WITH CHANNEL MASTER
When flashing channels to your STB some of the names may change. To correct that do this.
GO to MENU, then OPTIONS and set
"FULL CHANNEL NAMES" to OFF.
Load your CHANNEL.
When done turn FULL CHANNEL NAMES back ON.
ADD A TP
To add a TP go to the channel scan section, select Dish or whatever go down to the green screw driver and hammer icon, hit ok to enter the tp list, then F1 button to add new TP You can also hit the pause button in this section to get a overview of other actions.
HOW TO TURN AUTO-ROLL OFF & ON
MENU,OPTIONS then go to AUTO-ROLL. If there is a problem sometimes getting the keys to auto-roll take the STB off a local channel that may help.
SET GMC TIME
MENU, INSTALLATION, TIME SETTING.
TO SEE WHAT BIN & BOOT YOU HAVE
MENU, INSTALLATION, RECEIVER UPGRA, OK
RESET RECEIVER (HARD BOOT)
Sometimes you need to do a reset, (hard boot). Turn power off then on from the back.
It is a must for users to have tools to get the keys. Below is just to get you started.
KEYMASTER or KEYRIPPER - Will give you keys.
HOW TO CLONE ONE XTREAM TO ANOTHER XTREAM
Connect the Master Xtream (the one with the info) to the wall outlet and TV & have power on from the back of the Xtream.
Connect the second Xtream (the one you want to clone to) to the wall outlet with the power off in the back.
Connect the master and clone receivers together with a null modem cable.
On the master receiver click on MENU, INSTALLATION, RECEIVER UPGRADE, ALL INFORMATION, then OK.
Turn the to be cloned receiver on from the back and the transfer will start.
When the transfer is done it will take about a minute for the clone receiver to process the info. Make sure you give it plenty of time to finish.
CLEAN AND PUT LUBRICANT ON YOUR REMOTE.
If you have trouble with your number pad on your remote you can use ProGold G100P from Radio Shack to clean it, part number 64-4337
SOME OF THE ON LINE TV GUIDES
DN TV PROGRAM GUIDE
h**p://www.dish net work.com/content/programming/programming_guides/ (take out space & add 2 T's)
OTHER
h**p://www.bell****/shop/en_CA_ON/PrsShpTv_Landing.page
DN CHANNEL CHART
h**p://www.dishchannelchart.com./
LOCAL TV CHANNELS
h**p://tv.yahoo.com/grid?lineup=us
OnSat TV LISTING
h**p://www.onsat.com/listings.php
CREATE YOUR OWN TV LISTINGS.
h**p://tvlistings3.zap2it.com/
ASIA PROGRAM GUIDE
h**p://www.apsattv.com/
FIND SATELLITES & WHERE TO POINT DISH.
Satellite Finder Web Sight. A program that will let you know where to point your dish for a Satellite.
h**p://vps.arachnoid.com/satfinder/
Need to find a Satellite
h**p://www.nerosoft.com/SatCalcView.asp
Another Satellite finder
h**p://www.emantechnology.com/lookangle.asp
Footprint for 91.W
h**p://www.kusat.com/go.php?path=/install/foot-display.php?nickname=nimiq
FIND A SKEW
h**p://www3.telus.net/rampage/skew.htm
Linear Mode
