Auto rolling?

[db7344]

Downloaded new bin file but still A/R. Anyone else having same problem?

[bigboi2005]

I'm having this problem right now also! Any other?? I'll try and flash it again and see what happens!!

[blueomega]

sometimes you have to check your sat set up to make sure your settings didn't change like changing sat type to standard etc

[jimilives]

I too am getting just auto roll on the newest bin, at least it isnt locking up like yesterdays did, that one didnt work for me at all.

[bigboi2005]

It's up and running, i guess it just needed some time...took about 10 minutes or so but it's working like a charm! Thanks for the quick response though, appreciate it!

[boboisno1]

Patience guys. The last ecm is trickier and new bins take longer to give you a picture, you will also see this when changing channels. Everyone is having this problem.

[jimilives]

ok cool thanks for taking time to let us know you had success, I guess i will go pour a coffee and stop being so quick to say its not working, been about 7 minutes here only 3 more to go lol, will post back if it doesn't work after that.

[furhzy]

I 'am having trouble just keeps auto roll, ? is the com-port suppose to be set at com 1 for viewsat-xtreme?

[daredevil]

Originally Posted by jimilives

I too am getting just auto roll on the newest bin, at least it isnt locking up like yesterdays did, that one didnt work for me at all.

make sure your autoroll setting is set to all
if as the previous poster mentioned you have waited at least 10-20 minutes on the initial load of the bin be patient, b ut after 20 minutes something is wrong - yes there is also a delay when you change channels even with this new bin. to be honest a lot of wierd and differing problems today for different people but the best course of action has been the following - basically start from stratch THIS IS NOT TYPICALLY NEEDED but when you have check all your setting and know the bin is good - start from scratch - I have helped a fe w people out today with freezing (including myself with new bin on b/v - yes todays new bin from on me on b/v) and a lot of autoroll issues this has fixed the issue in a few cases...

FIXED:

- Do factoryt default - reset .. then

Using loader 2 I...
1. loaded the factory bin from this site
2. Loaded the 05 bin out today
3. Loaded my default.SAT satalite file
4. Loaded todays opkey hex (created opkey just now using vskey 2.6)

Then
re-do your antenna setup for each sat **** if you dont know what this is write them down before your reset**

Channel scan for each sat and you should be rockin * note sometime the channel scan has been giving people grief so if after the channel scan above and you weait for the channel to come in - if it doesnt then go to the first loader2 step above (ie dont factory reset) just the loader stuff which also means your antenna setting are fine and no channel scan needed...


still get the delay when switching channels BUT NOT COMPLAINING have b/v and d/n so couldnt be happier

thanks to the coders

[bigboi2005]

Its up but i am now having some trouble, like boboisno1 said it not only took a while for the picture to come up but it is also auto rolling every time i change the channel. Checked settings, they are normal! As long as its up i don't really mind the delay in changing channels all that much! At least its up, thanks again to the programmers!!

[jimilives]

Have b3v but not DN and have given it about 25 minutes, no biggie, happy to have one at least, but may try and do a fresh install and rescan just to be a bugger, with my luck I will get it working just in time for this bin to be blocked lol

Cheers all

[PASQUALINA]

AutoRoll problem a fix is required. Does anyone have a remedy?

[daredevil]

Originally Posted by bigboi2005

Its up but i am now having some trouble, like boboisno1 said it not only took a while for the picture to come up but it is also auto rolling every time i change the channel. Checked settings, they are normal! As long as its up i don't really mind the delay in changing channels all that much! At least its up, thanks again to the programmers!!

the autoroll when changing channels (30 seconds to a minute) is a KNOW issue with this bin and we have to live with it. IT IS NOT YOUR SETTINGS

but I am pointed at 91, 110, and 119 and all are up and all channels - so if you fall short of that and it's important to you read my previous post and start from scratch and redo - somnething we typically dont need to do...


The autoroll delay when changing channels will no doubt be fixed in a new bin down the road - at least we have all the channels :-)