While no guide can cover every possible combination of lnb's
and switches, I have included the most popular set up's.
What you'll require to complete your initial set up.
1; Neosat Ipro 1000 receiver
2; A serial cable, probably came with your receiver.
3; A high speed internet connection, dial up has been shown to work but
high speed is recommended.
4; A router
5; Sufficient Cat 5 cable to reach from your router to where your
Ipro will be located, or a wireless game link similar to Logictech's
Next go to
NeosatUSA and click on SUPPORT then DOWNLOAD
and download;
A; Ipro1000/Neosatlite Uploader
B; Ipro1000 Factory Firmware ( not required for initial set up but might
be needed some time later )
Next return to this site, go to Official Downloads and download;
A; Neosat Ipro1000 IKS 1.0 or the latest bin file
B; Channel Master Support Bootloader 1.26, you'll only need this if
you intend to use Channel Master
Unzip all the files to the same folder and then create a shortcut for convenience.
Connect the serial cable to the Ipro and your computer, Open the uploader program
and choose IKS 1.0 as the file you want to load. If you click on the " Com 1 button "
you can change to your correct Com Port. Click on " Start Down" and a screen will appear
instructing you to reboot after clicking OK, Click OK then turn off your Ipro
using the back power switch, wait a few seconds and turn back on. Wait for
file to download. You have just downloaded the only file absolutely necessary
to make your Ipro work.
Optional; Open Neosat Uploader and choose Bootloader 1.26 as the file to
open. Choose the correct Com Port as before, Click on the " Main " button
and it will change to " Boot " Click on " Start Down " and continue as previously
explained. This step is only required if you intend to use Channel Master.
Next connect your Ipro to your TV and Satellite feed, Internet connection is
not required yet.
The next steps depend on the type of LNB's you have, I have included what
I believe are the three most popular setups, if you have something different
please post and we'll do our best to assist you. All three combinations have
been proven to work by me, there are of course variations so do what works
for you.
Turn on back power switch and press the red power button on your remote.
After the Ipro boots up press MENU > INSTALLATION > ANTENNA SETTINGS
For Dish Pro Twin, Dual or Quad;
Satellite = Don't change this setting
Lnb Type = Twin DP LNBF
Lo Freq = 11250
22 KHZ = Off
DIsEqC Mode = Port 1
Multi Dish Switch = Disable
DIsEqC 1.2 = Off
0/12V switch = Disable
LNB Power = On
Search Channels = Ch All Search
Highlite Search Channels and press the " OK " button on your remote, both
the 110 and 119 Sats should scan.
For Legacy Twin ( sometimes called the fat legacy )
Satellite = 119 Echo 7
Lnb Type = Standard
Lo Freq = 11250
22 KHZ = Off
DiSEqC Mode = Legacy Twin LNB 1
Multi Dish Switch = Disable
DiSEqC 1.2 = Off
0/12V switch = Disable
LNB Power = On
Highlite " Search Channels " and press the " OK " button on your remote,
wait for the 119 sat to scan.
Satellite = 110 Echo 6,8
Lnb Type = Standard
Lo Freq = 11250
22 KHZ = Off
DiSEqC Mode = Legacy Twin LNB 2
Multi Dish Switch = Disable
DiSEqC 1.2 = Off
0/12V Switch = Disable
LNB Power = On
Highlite " Search Channels " and press the " OK " button on your remote,
wait for the 110 sat to scan.
For Legacy Singles using a SW-21 Switch
Satellite = 110 Echo 6,8
Lnb Type = Standard
Lo Freq = 11250
22 KHZ = Off
DisEqC Mode = Disable
Multi Dish Switch = Sw-21 Dish 2
DiSEqC 1.2 = Off
0/12V Switch = Disable
LNB Power = ON
Highlite " Search Channels " and press the " OK " button on your remote,
wait for the 110 sat to scan.
Satellite = 119 Echo 7
Lnb Type = Standard
Lo Freq = 11250
22KHZ = Off
DiSEqC Mode = Disable
Multi Dish Switch = SW-21 Dish 1
DiSEqC 1.2 = Off
0/12V Switch = Disable
LNB Power = ON
Highlite " Search Channels " and press the " OK " button on your remote,
wait for the 119 sat to scan.
Next press MENU > USER SETTINGS > LOCAL AREA and choose the State and
City
Then press MENU > SYSTEM SETTINGS > TIME SETTINGS , at minimum
set Time Adjustment, Summer Time, and Clock
Turn off your Modem, Router and the Ipro (using the back switch)
Connect the Cat 5 cable ( or your wireless pieces ) between the router and
your Ipro.
Turn on your Modem and Router and let them boot up.
Turn on your Ipro and you should be watching TV.
I hope this guide will assist you and make initial start up easier and quicker.
Good Luck.
Linear Mode
