61.5 & Bev

[lets]

I have a buzz s2010f. I have 110, 119, 61.5 & 91 hooked to it. I get the channels from 110 & 119 (some are scrambled), but I don't get the ones for 61.5 & bev at all. I did have the 61.5 channels in October, but lost them when the new November file came out. When I scan 61.5 & 91, I get the channels for 110 & 119 repeated (scans 110 & 119 again).
Could somebody please shed some light into this?

Many thanks and Happy Holidays.

[carpenter1]

What are your settings set too?
Do you have separate antennas and do you have a switch?

[lets]

Carpenter1, I am quite new to FTA. Somebody set my buzz. I can't always get a hold of him. I prefer to do this on my own. I want to learn. I have paid in the past and this is where it brings me to. Thanks for your patience.
I don't know which settings you mean, thus I give you everything I think is pertinent.

A/V- NTSC
Autoroll-on
Auto tp-on
boot loader 01.11
main software-02.35-P
+++

For SAT:
LNB-on
LNB type-single
22khz-off
search options- all
network search- on
Diseqc- for each sat I have the different ports on: Port 1 = sat 61.5, Port 2 = sat 119, Port 3 = sat 110, Port 4 = sat 91(nimiq).
Motor- disable
legacy switch-off.

I have one dish for 110 &119, one dish for 61.5 and one for 91, all hooked to the 4x1 diseqc & into the receiver.

[perezcuco]

Originally Posted by lets

I have a buzz s2010f. I have 110, 119, 61.5 & 91 hooked to it. I get the channels from 110 & 119 (some are scrambled), but I don't get the ones for 61.5 & bev at all. I did have the 61.5 channels in October, but lost them when the new November file came out. When I scan 61.5 & 91, I get the channels for 110 & 119 repeated (scans 110 & 119 again).
Could somebody please shed some light into this?

Many thanks and Happy Holidays.

If you get the 110 channels when you scan 61, that means that your antenna is pointing to 110.

[lets]

Hey guys!
Thanks for your input.
I am presently viewing the channels from 61.5. My problem seems to be with the transponder. I did a factory reset & started by scanning the 61.5, after checking which transponder was giving me 100% quality. I got nothing. I started over & on the 3rd try, got the channels. I didn't get 615(RTPI) & 650, but got the Brazilian. I tried the same for the nimiq (4 tries), but it didn't pick up any channels, except the echostar ones, which are the 110/119 channels with a 2 in front. Then I scanned my 110 & 119, got their channels.
Now when I change away from the 61.5 channels, I get the 110/119 channels (a few with no signal). To go back to the 61.5 channels, I have to go into menu & switch to a transponder that gives me 100% quality (every time) et voila, I have a signal & can view.
I hope this helps the ones that have the same problem, even though temporary.
Could it be my diseqc? I have a $5 one. I was told that there are $50 ones that make a difference. I would appreciate an honest answer (no dealers).
What can I do to keep the quality at 100%, after changing channels?
Will a frequency booster help? I would like to get my nimiq going as well.
Many thanks in advance and Happy New Year.

[mellwood]

hey guys i cannot find anynimiq sat on my sat list on pansat2700a

[carpenter1]

lets
It does sound as if you are having a diseqc problem but it can also be a program problem.
Load this file for your receiver and try again>> http://www.abadss.com/forum/buzz-gen...se-13-dec.html