Ready to Download

[happygilmore]

Hi,

I just got my sonicview 1000 and I'm hooked up to the computer. I just want to make sure this is right before I begin.

The most current downloader I found was V0201, then I found two fixes: (auto roll fix - 10-27-06 & new fix -11-01-06.) Do I load these at the same time I load the downloader?

Thank You

[SatelliteJunkie]

Originally Posted by happygilmore

Hi,

I just got my sonicview 1000 and I'm hooked up to the computer. I just want to make sure this is right before I begin.

The most current downloader I found was V0201, then I found two fixes: (auto roll fix - 10-27-06 & new fix -11-01-06.) Do I load these at the same time I load the downloader?

Thank You

Download the Loader first. Be sure to unzip / extract files prior to use of utility.
A rule for bin files: Always use the newest version (latest date). So in your case go with 11/01/06.
Remember to also unzip / extract bin files prior to loading.

[tango]

Originally Posted by happygilmore

Hi,

I just got my sonicview 1000 and I'm hooked up to the computer. I just want to make sure this is right before I begin.

The most current downloader I found was V0201, then I found two fixes: (auto roll fix - 10-27-06 & new fix -11-01-06.) Do I load these at the same time I load the downloader?

Thank You

Easier way to send file to your SV-1000
This works for out of the box and updating your SV-1000
Download SV loader v0201 here.
Download the latest bin as well.

Connect the null modem cable to SV-1000 and your PC.
Turn the SV-1000 power on with rear switch and the remote.

Open the downloader and connect to com port your using to flash and then go back to stb tab and select Downland file PC>>STB and select the bin you want to flash to your SV-1000 and doulble click the bin you want to transfer to your SV-1000.

Transfer will begin Without flicking the rear switch IF the rear switch is on and the power to the SV-1000 is turned on with remote prior to sending the file to the box. YOU can even do this when itis hooked to your TV so you can see the progress!!

On the TV screen it will say Software Downloading. Just let it run and on the SV-1000 display you will see dn:00 and will count to 100%. At the end a blue box will appear under the red software Downloading box that will say "Flash Updating" and then the SV-1000 display will do through a short process of procedures and say---,Boot,boot and wind up on your last previous channel or no channel if it's out of the box. DO NOT interrupt power to the SV-1000 during this process.

If your SV-1000 is out of the box, do to menu,System Setting, user Options and turn everything on except Auto Dolby select. Set the correct date and time. Select your A/V prefrence in the A/V settings in the menu. Then you'll need to set up your lnb/switch config in the Installation menu and red button scan each sat as you set them up. Then put on ch 200 on dn or 2417 on b3v and wait for keys to roll. this could take 5-10 min on each provider.

[happygilmore]

Thank both tango and SattelliteJunkie, it was very easy to set up and get it running.

[blindside29384]

i have the loader but i have a usb to null cable my loader does not transfer the barr never goes up and i tried all the comps am i doing something wrong ?

[boboisno1]

Sometimes when such old posts like this one are reopened people have a tendency to skip anything that someone may be asking. For the future to help you get better responses to your questions you're better off starting your own thread. I'm going to copy your post and start a new thread for you in the same help section as this post.

Click here for your post 613Cressy

Originally Posted by 613Cressy

Happygilmore
Just read your cry for help in 2006... I have the same prob. that you stated. Everything works correctly up to the download taking place in the "Downloader". The window comes up, but the progress bar shows that nothing is happening. When I / stop the window says "download failed."
Any help would be appreciated.
Thanx