help looping two nfusion solaris - ABA DSS

trew2u · September 15th, 2009

How do I get two nfusion solaris to work at same time. I have both systems connected to eithernet; bin files downloaded and both will work. The problem is when I try to watch both at the same time, one system will freeze and disconnect from Suns. I have checked the settings (installation, system and user), internet settings, network info; everything seems to be where it should be. I have strong S & Q.
Any and all help greatly needed.

Thanks.

**snakebite** · September 15th, 2009

you need to run seperately with switches ,what are you running for lnb and dish?

trew2u · September 15th, 2009

LNB is -single DPLNBF-
multi-dish switch is off.
Do I need to change multi dish switch to on? and change the LNB?

trew2u · September 17th, 2009

I think i misunderstood what you were asking. I have a single eye LNB and a DN dish. hitting of off BEV for right now. When you say run seperately with switches what do you mean. sorry to sound like I don't know much, but I don't know much, yet.

**snakebite** · September 17th, 2009

i also misunderstood also. you are only running 1 sat with a single lnb? it only has 1 cable comming from lnb?

**snakebite** · September 17th, 2009

DN Legacy Single and DTV Single LNB

is this what you have?

**chiswood** · September 17th, 2009

one lnb,do you have two wires from lnb to rec's?or one wire from lnb to switch,then two wires from switch to recs.

**snakebite** · September 17th, 2009

DishPro Single and Dual LNB

Identifying Marks
-----------------
DishPro markings
Single: One coax connector output
Dual: Dual coax connector outputs

do yourself a favour and get a dual lnb and you can run 2 seperate cables,one to each reciever.

trew2u · September 17th, 2009

I have a dual LNB with a dish 500. I have spent the last hour or so running two wires to each reciever. But I am still not able to run both TV's at the same time. one tv is on and working, then when i turn the other tv one, the both will recieve suns for a minute then the 1st set will freeze and stop working. I noticed a prong on the back of the nfusion for loop to other receiver. What is this for?

**snakebite** · September 17th, 2009

i run dual lnbs to 4 recievers and i use a zinwell 3x4 switch into diseqc for each sat and i also have everything grounded -switches and dishes.each lnb has the 2 out ports that i run to zinwell and off the zinwell i can run up to 4 seperate recievers.you might have to buy a switch.

trew2u · September 17th, 2009

Thanks for the info. I'll try the switchs and see if that helps. Is there a distance not to exceed on the coax? Mine is running over 100 feet from the house. (Thanks to the trees and hills.)

**snakebite** · September 17th, 2009

100 feet is starting to push it from what i have read.try it with the switch and running 2 nfusion recievers ,make sure they are grounded dish and switch.i have went through that with running 4 recievers and getting what your describing also.good luck with it.

trew2u · September 17th, 2009

will do. THANKS again.

trew2u · September 20th, 2009

I give up for now. waiting on new switch to come in. running one dish on BEV and the other on DN for now. Thanks again for all your help.

**snakebite** · September 20th, 2009

no problem ,let us know when you get switch ,and remember grounding is very important running 2 nfusions.drive a grounding rod into the ground next to the dish ,ground switch to the mast and then run grounding wire from dish to the rod.