vs pro auto roll processing

[chaswud81]

purchased viewsat vs pro tuesday, set it up, installed new file with new gui, most bev channels worked very well but I wasn't getting every channel so I tweeked a few settings and installed the file with old gui. played around trying to get all channels and next thing I new I started getting 'Auto Roll Processing'. I haven't gotten past that since. I have loaded Friday's file and still the same thing. I have installed software from viewsat and then the new file; again the same problem. I did get all channels to be picked up by changing the LND Freq from 11250 OCS-DP to just 11250. What could I have done to get stuck on 'Auto Roll Processing'?

[SoDarkTheCon]

Originally Posted by chaswud81

purchased viewsat vs pro tuesday, set it up, installed new file with new gui, most bev channels worked very well but I wasn't getting every channel so I tweeked a few settings and installed the file with old gui. played around trying to get all channels and next thing I new I started getting 'Auto Roll Processing'. I haven't gotten past that since. I have loaded Friday's file and still the same thing. I have installed software from viewsat and then the new file; again the same problem. I did get all channels to be picked up by changing the LND Freq from 11250 OCS-DP to just 11250. What could I have done to get stuck on 'Auto Roll Processing'?

Much easier to start all over...load the factory bin first, then the new file. Then setup all your settings...Can you please post your settings for bev nimiq 1 please ?

[chaswud81]

is there an easy way to save all settings to file on usb key?

[chaswud81]

Is there a way to save all settings to a file on usb key?

[SoDarkTheCon]

the settings are very easy to setup...i will get this moved to the proper section...

[chaswud81]

Sat Nimiq 1
LNB Power On
LNB Freq 11250
22Khz Tone Off
DiSEqC 1.0 None
DiSEqC 1.1 None
Legacy SW None
Motor Type Disable
Tp Freq 12224

[chaswud81]

reloaded factory bin;
reloaded Friday's bin, new gui
still getting 'Auto Roll Processing'; no change after several minutes

[SoDarkTheCon]

Originally Posted by chaswud81

reloaded factory bin;
reloaded Friday's bin, new gui
still getting 'Auto Roll Processing'; no change after several minutes

make sure autoroll is on, and leave it on channel 239...give ita bit of time to roll the new keys. But first do a hard reboot, but turning off the black switch at the back for a few seconds and then back on.

[chaswud81]

scan finds 416 TV and 84 Radio channels

[SoDarkTheCon]

ok...just let the autoroll do its job.

[chaswud81]

Auto Roll All ON
Auto TP OFF
Display CH Number by SID ON
Screen Saver Floating Info
Full Channel Name OFF
Local Setting 1. Abilene, TX (default)
Local Channels OFF
Bell-vu Ch Mapping ON
Auto Diseqc OFF

tuned to channel 02239
did a hard boot
still Auto Roll after several minutes

[SoDarkTheCon]

Originally Posted by chaswud81

Auto Roll All ON
Auto TP OFF
Display CH Number by SID ON
Screen Saver Floating Info
Full Channel Name OFF
Local Setting 1. Abilene, TX (default)
Local Channels OFF
Bell-vu Ch Mapping ON
Auto Diseqc OFF

tuned to channel 02239
did a hard boot
still Auto Roll after several minutes

my bad, you got bev...try channel 503

[chaswud81]

trying 02503 CP24

[chaswud81]

still processing

[chaswud81]

approaching 30 minutes of processing. Any other thougts?

thinking about going in and zeroing out all of the BEV codes. Would that at least tell me if auto roll is doing anything?

[SoDarkTheCon]

did you do the hard reboot ?

[lmarrero]

I'm paying close attention to this thread since i'm having a similar problem... I get all the Echo but most of the channels on Nimiq say the Auto Roll Processing... i just bought the box yesterday and downloded the lastest file. VS Pro...