No Channel list with VS Ultra bin

[Soycazador]

Hello guys. I've loaded the new BIN file for my VS Ultra but I'm not getting any signal on any of the channels. Setup looks good, Channel list is there, TP's are there. Any Idea of what would i need to do? I've rebooted also from back switch. Any advise will be greately appreciate it.

[fernrascal]

where did you get the file from because mine is working fine

[monoxid]

In order to help you , we need to see your settings. It could be a very simple thing, did you review all your settings?

[Soycazador]

Yes, my settings have not change from previous bin. Here are my Sat settings
110.0W
LNB (ON), LNB Type(OSC-DP), LN Freq(11250), TP Freq(1224), Search Opt(All).
119.OW
LNB (ON), LNB Type(OSC-DP), LN Freq(11250), TP Freq(12239), Search Opt(All).
I have the right DiesQc port for both of them and bot 22khz set to Off

[Apocalypse_67]

Reload the BIN again and tune to channel 200.
BTW, make sure that it's the latest working BIN.

[monoxid]

Did you try to reload the latest Bin? Your setting look good.

[Soycazador]

Hi there Apocalyps. Ok I have reloaded the bin and still no succes. I do notice that on the Sat setup the Sat is not been sync . U know, u set up the Sat u want and a bar above should mach the Sat that u chose. That's the part that is not in sync. Any Idea why?

[stlucas]

I just load 080504 on mine evertthing is working,not more then 3 minutesago

[Soycazador]

Yes, I've reloaded the bin. but no succes.

[mvideanewbie]

I'm having the same problem

[Apocalypse_67]

Re-check your Diseqc ports. If the top display is not matching the sat that you are assigning, then you need to check that your dish has not moved.

SATELLITE............Echo 8,10 110W
LNB POWER.........On
LNB TYPE.............Standard (OCS-DP if using DP LNBs)
LNB FREQ.............11250
22KHz...................Off
TP FREQ...............12224
DISEqC1.0..............Port 2
MOTOR..................Off
LEGACY SW..........None

SATELLITE............Echo 7 119W
LNB POWER.........On
LNB TYPE.............Standard (OCS-DP if using DP LNBs)
LNB FREQ.............11250
22KHz...................Off
TP FREQ...............12239
DISEqC1.0..............Port 1
MOTOR..................Off
LEGACY SW..........None

[Soycazador]

Yeah seetings look good. I went out to see if dish was not stolen (it can happen i've seen it before) but dish is there and i dont think it has moved, we have not have like strong wings or any extreme weather. It's weird. First time i have experienced an issue like this current one with bins before. Any other reason u can think of?

[Soycazador]

Do u think that a Factory reset is necessary at this point to fix the problem i'm having with my box?

[Soycazador]

Hi, have u resolve the problem u are having similar to mine?

[Apocalypse_67]

Originally Posted by Soycazador

Do u think that a Factory reset is necessary at this point to fix the problem i'm having with my box?

Load the last file that was working (080424U) if you get channels and picture, then the new file you got is bad.
If the problem persist, load the latest Fact File (V132) then load the latest BIN, change your antena settings and auto scan your sats.

[Soycazador]

Weird problem. I've done the Fac v132 then lates bin. I also tried the previous bin and having same issue. I have a pansat 3500sd and I'm watching tv there(no ppv cuzz no new bin out) but that's how i know that I am getting good signal from Sat. But my viewsat is a no go still. Is there a possiblility that I lost the sat info even tho i see them there or any part inside the box that is not working any more? I only get about 2 lines of signal strenght from the Sat. Maybe this will help think of anything else that might be going on? I really appreciate your help guys.. this site is awsome and I always come here for advice.