need help with channels

[wdw2050]

hello im kinda of new to this but i follow the steps and still confuse. well my setup is:
dishpro 1000 hook into port 1 no switch straight to reciever
sv 8000 hd with board
got signal strength on 110 s:78 q:100 but 119,129 i see s:0 q:100?
i scan all of them and got channels but got alot of duplicates and no radio channels? also i dont get all channels like MTV,BET are my locals which is Los Angeles but i get locals from other places? how can i get all the channels and my locals? also how do you use the CM program if you dont have the port of yout computer? can you used the usb drive to edit channnels in CM please help are point me to the right documents
thank you in advance

[Mighty Thor]

in sat setup on your box make sure you have 119 set to port 1, 110 set to port 2 & 129 set to port 3

Please list your sat setting also is the small lnb hooked to the large lnb (lnb in port)

[Landscapeman]

Post your receiver settings

[Landscapeman]

Have you made sure of your dish alignment? The reason you are getting multiples is from multiple scans. You should have your settings as follows:

Sat: 110, 119, 129
Power: On on all
freq: 11250 on all
22khz: Off on all
TP: 12224, 12239, 12224
Port: 110-2,119-1,129-3
Motor: Off on all
legacy: Off on all

[wdw2050]

110 port 1
119 port 1
129 port 1
i plug the cable into port 1 on my lnb do i need to plug cables in port 2 and 3?
i have the Dishpro 1000 with 3 lnb and 1234 ports on it

[Landscapeman]

You only need one cable from the dish. Change your receiver settings: Port1 119, Port2 110, Port3 129. Give that a shot and post back.

[yamahadude157]

do not change the location of the cables, just change the settings in your receiver.

[jayjay1972]

make sure your settings are correct. Follow the ones that are posted above by landscape and M Thor. Make sure you do a regular scan not a blind scan. The blind seems to pull in lots of dups. In your settings you must get a confirmation on the top right hand corner that matches. For example echo 8 will say echostar 8 (110), echo 7 will say echostar 7 (119), echo 5 will say echostar 5 (129)

[wdw2050]

ok doing it now and do i press scan all are press scan sat on each one?

[Landscapeman]

Scan all. Once you get all your channels we will handle the multiple channels.

[Landscapeman]

To scan all you need to make a check mark next to the sats you want to scan. You can use your remote when scrolling thought the sat menu hit the little blue button on your remote. It will make a check, do this next to 119,110, and 129. Then scan all.

[jayjay1972]

Originally Posted by wdw2050

110 port 1
119 port 1
129 port 1
i plug the cable into port 1 on my lnb do i need to plug cables in port 2 and 3?
i have the Dishpro 1000 with 3 lnb and 1234 ports on it

the single lnb goes into the twin lnb "in". The twin has built in switch so it carries all 3 signals in each (out) cable. Run it straight to your reciever and adjust settings. Your diseqc 119#1 110#2 129#3

this is your dish right?

[wdw2050]

mines dont look like that its one big lnb also it scan 110 ok but 119 nothing came thru the scan all failed but 129 alot of channel and the radio is comming thru so it finish scanning then what thnx guys for your help i been dealing with this since 1200 pm lol