step by step 82.0 solution - ABA DSS

cakegetter · July 15th, 2009

Ok everyone I have the step by step solution to get that pesky 82.0 and failed to upload message here it goes, and remember you have to follow step by step. you will need sysclean bin, factory file bin, 445 bin and 460 bin.

Step #1: Installing bins in exact order I have and do a hard reboot after each bin is installed.
1) install sysclean bin
2) factory file bin
3)445 bin
4)460 bin

Step #2: (IF YOU HAVE VISTA TURN FIREWALL OFF)Run ms dos and type ipconfig and hit enter, write down the IP address and subnet mask you have for the ethernet adapter local area connection. There will not be a default gateway.

Step #3: Connect Ihub into your box and turn it on. Plug ethernet cable from Ihub straight to your computer. STRAIGHT INTO YOUR COMPUTER NOT ROUTER.

Step #4: Open wiznet and click search, once it reads your ihub go to the options tab and put 0 in inactivity time, time, size and char. Make sure password and serial configuration are disabled(enabled is not checked). Once you do that click setting and it should save.

Step #5: Go back to network tab and in local ip and subnet write down the address that you got from ms dos in step #2. Leave gateway as it is and make sure you put 1920 in port. Uncheck use dns and above in server ip put 77.93.75.89 and 1920 in port. Now check use dns and put the same address you have for gateway down. In domain name write WWW.SVFTAIKS.XXX (xxx as in male orgasm lol) I hope you guys are not too stupid to get that. Now click dhcp and then click setting and it should save. Click upload and install rom0100 and once that is finished click upload again and install 1.4

step #6: Close wiznet and reopen it. You should see 1.4 in the version box where 82.0 used to be. If you do, you have successfully installed 1.4, now unplug ethernet cable from computer and plug back into router. Get bin 462 and install it to your box via usb and do a hard reboot. Once you do that you should have IP config back in your stb menu. Now once you have IP config back go to it and setting type should be DHCP in use dns put no and in the server IP write down 77.93.75.89 and apply ok. GO back to ip config, now put use dns back to yes, Server port should be 1920 and of course write down your unique Ihub serial number and hit apply.

Now you should be able to watch tv, This is the best I could do and I tried to write down as specific as I could but I am not that good with words so pardon if you did not understand some of my explanations. GOOD LUCK.

basscat02 · July 15th, 2009

Hey Cake, great post, It is now a sticky in the sonicview area.Thanks
bc02

purpleman · July 15th, 2009

great write up -- thanks alot -- fast question -- does version 82 have anything to do with me not seeing ip config on reciever? i have it all hooked up , but unable to get that on reciever b4 i try above, thanks

stlucas · July 15th, 2009

With all the prolbem everyone is having with the unit does it make it worth buying one at t

his time.

purpleman · July 15th, 2009

well, i would say yes -- once everyone gets it goin -- unfort im having troubles, so trying to learn and correct problems so can move on -- thanks 4 ur commetns

**hhawg1** · July 15th, 2009

Am I the only one out there still having trouble with this? Man I've gone through this procedure several times now and still no upload. When I open Wiznet and do the search, it see's a card but I'm still getting the ver. 82 and "not connected. And I'm plugged directly into my laptop from the IHub!
Thought I was somewhat computer/ network savvy but this is really frustrating!

**hhawg1** · July 15th, 2009

I really think it's a problem with the IHub not being recognized by the STB. I've read other posts here where you plug in the IHub, fire up the stb and will take 30 seconds or so to interface. My stb has never done that. Ever. I've booted the box the IHub in. Bo0ted the box and then put the IHub in. Numerous times and never seen any indication from the stb that it see's the hub. I don't see the ipconfig on the menu either.
Do I have a bad IHub ya think??

bassist · July 15th, 2009

hhawg, after you get yours figured out, you will probably be able to improve on cakegetter's procedure or explanation. It looks like Cakegetter has done a really good job of getting the ball rolling. ABA is great place b/c there is a lot of expertise and very little ego.

purpleman · July 15th, 2009

I agree with all your threads -- H HAWG , im on nite 2 of trying to figure this out -- i have exactly same questions you have -- done every upload in book above and upload failed -- i agree - i dont think ihub if reading anything? i have no ipcong either. i wish someone would explain that. -- when does that show up ? soon as you plug in ihub and hook up to desktop? also -- does reciever give any indication of external module like it did when i added 8spk board? i am truely stumped, spent 200 bucks on ihub and also 2 net gear power line adaptors and 2 nites wasted --. i am gonna give up -- unless someone can help wiht basic answers -- when should ipcong on reciver show up? does that have any impact on WIZNET -- also when i try to hook ihub directly to computer, i need to take out my cable/internet provider feed as i only have 1 outlet in back for that kind of jack . . looking for more answer and suggestions for 2 nites of fustration.

purpleman · July 15th, 2009

HHawg - what do you mean sees a card? i can go threw manual changes address's as top thread, but always fail upload and not connected never connected every

imlost32 · July 15th, 2009

ppl who are having trouble can pm me and i can help u step by step on an im well thats whenever im on all thnxs go to cakegetter for showing me how!!!

dblj67 · July 15th, 2009

I just got in on this but just a quick note... ipconfig is a program you need to run from ms-dos on your computer it is not going to just pop-up. from what instructions say you need to run that to get ip info for your ethernet port.

**hhawg1** · July 15th, 2009

It shows a mac address for one device in the list in the Wiznet(?) box. But it still shows the version 82 and Not Connected. I "assume" that means it see's the IHub but if so, why won't it upload? Also I don't see the ipconfig on the menu screen anymore of my SV8000

**timvui** · July 15th, 2009

can some one help me what is the rom0100 pls?

dblj67 · July 15th, 2009

am i missing something? i cant find 445 bin?

purpleman · July 15th, 2009

hhawg -- u there - this is what i did, and it worked, loaded fact bin file, clean file - bin 445 460 - but key for me was i left the ihub hooked up to router for bout 30 mintues , then out blue i was reading and looked up and saw network adaptor thing appear on black screen -- i then went to desk top and did cartakers instructions , came and it uploaded and worked, so leave it hooked up for while man, confirm u got this

**hhawg1** · July 15th, 2009

Will try that now. Thanks

Gaspo2k · July 16th, 2009

Hi there, im also having trouble with my ihub, the ipconfig on the receiver shows up but it says device not ready and when i go downstairs to the computer the wiznet doesnt recognized anything is blank in all fields, no version number or nothing, im using a powerline adapter and all the lights are lit and same for the ihub. Please help

cakegetter · July 16th, 2009

I just got home and am glad to see that this is working for some of you, all it takes is a little patience. If you follow the instuctions step by step I'm sure it will work trust me. It took me almost 3 full days of trial and error before I got it to work and credit goes to dogg from another site who got the ball rolling, and with a minor few tweaks I was good to go. If you are still having trouble try steps 2 to 5 all over again and I guarantee it will work, it just takes patience. Good luck guys.

**timvui** · July 16th, 2009

where can i found the rom0100 pls?