[Sync45]

I thought this might help a few people out so here you go.
Problems with the iHub not communicating with the receiver/not taking the files/v82


This has been tested and said to work great. The results will have you up and running with v1.4 and a debricked iHub.

This is basically the exact steps taken to get the iHub back to life and upload 1.4 from the dreaded v82.0, this is also going to fix the receiver not detecting the iHub as well. - Follow the below steps EXACTLY as they have been typed, if you RUN in to a problem at all during any of the steps, please post the problem.

This will work as long as you have a router, and as long as you have a working iHub (one that lights up on back), and as long as when you plug the iHub in and press Search, and at least some sort of iHub info shows up, if it does, then this is what you will need to do.

This is all based on a linksys router with default gateway of 192.168.1.1 - majority of routers have the same gateway ip.

Something to check before you get started with the steps. Make sure you are directly plugged in to the first port on your router (with your computer in 1st port) and modem connection or dsl in the one furthest to left. Go to Start>Run>CMD>ipconfig

Make sure your Local IP is 192.168.1.100 and default gateway of 192.168.1.1, if not then I am not sure these steps would apply to you as well.

Make sure you have done:
Factory Default file from USB to receiver
Sys Clean file from USB to receiver
Hard reboot (back switch)
Load 206 Bin (for elite receivers only This is June 30th fix)(if your receiver is 360p-June 30th Fix or 8000hd-June 30th Fix is the correct fix file for those receivers with this step)
Hard reboot (back switch)

First step.

1. Connect iHub to receiver

2. Leave Power on, on the receiver, but turn power off from the front panel (so that the time is displayed)

3. Connect ethernet cord to iHub, then directly in to ethernet port on computer, this part is where it is tricky and you might have to wait until you see "limited or no connectivity"

4. Open up the WIZ program, click search until it displays the fields with some sort of info. Once it does, your in luck! Now you need to skip around a little for this next step.

4 1/2. Make sure Static is checked, you should now see the fields able to change settings. Make your settings match below settings.

Local IP: 192.168.1.101 Port: 1920
Subnet: 255.255.255.0
Gateway: 192.168.1.1

Operation Mode: Mixed

Make sure USE DNS is checked!!!

DNS SERVER IP: 208.67.222.222
Domain Name: WWW.SVFTAIKS.COM

Now click on Setting, if it gives you an error after clicking, click setting again until it takes. Once it does, close the WIZ program and follow on to next step.

5. Now that you can see the iHub current info and the settings, now what you want to do is check on the back of your router, this part is crucial... Make absolute certain that your PC is plugged in to the first outgoing port on the router. And now unplug iHub from back of computer, plug it in to the 2nd outgoing port on the router (the ip that the router assigns to this port should be 192.168.1.101 by default.)

6. Open up WIZ program again, and click on Search until it finds your iHub, notice that the settings should read what I typed above? If it does then continue on, if not, then go back and retry until it does!! So now that it says the settings that we want it too, we still see the v82.0 right? Lets get rid of that now.

7. Go to Start>Run>CMD>ipconfig

Now type: ping 192.168.1.101 (if you get a series of replies, we will be able to load 1.4 with no problems at all!) Thats right, you can click thanks!!

8. Now bring the WIZ program back up, and I want you to click on Upload tab, you should be able to at this point, make sure you have extracted the 1.4 bin to your desktop. and then choose that file. You should instantly notice it start uploading with little bars with pretty much no hanging at all.

9. Once it says Completed, close WIZ, then reopen it, notice a new version?

10. Thats it, that should fix the problem

Additional steps to load bin 209 (for elite users only)This is July 11th fix for all 3 receivers(latest fix). You should see Network device connect! after rebooting receiver with iHub plugged in.

Then just put bin 209 on USB stick, upload, reboot, and you should be good to setup all your settings as before - Also, you will now be able to see your IP Config menu again and able to change settings at will.

Let me know if you get it fixed and up and running, this should fix the problems with the iHub not communicating with the receiver/not taking the files/v82 error.
__________________

[zekester]

Hey Sync, I know this is a copy paste, cause i've read it somewhere before. I've highlighted in black and underlined(Factory Default file from USB to receiver) a part I have never, never heard of in the 10 yrs I've been doing this, maybe it's a typo.
See highlighted part below.
Also most peoples DNS Server IP is the same as their Gateway, just point out that the DNS SERVER IP in your thread is no where near the same as your gateway.
If this is based on a GATEWAY of 192.168.1.1 although my router assigns a 0 in place of the fist 1, why is his DNS SERVER IP different from his gateway??
Could it be his ISP giving that funky number 208.67......??
.

Originally Posted by Sync45

I thought this might help a few people out so here you go.
Problems with the iHub not communicating with the receiver/not taking the files/v82


This has been tested and said to work great. The results will have you up and running with v1.4 and a debricked iHub.

This is basically the exact steps taken to get the iHub back to life and upload 1.4 from the dreaded v82.0, this is also going to fix the receiver not detecting the iHub as well. - Follow the below steps EXACTLY as they have been typed, if you RUN in to a problem at all during any of the steps, please post the problem.

This will work as long as you have a router, and as long as you have a working iHub (one that lights up on back), and as long as when you plug the iHub in and press Search, and at least some sort of iHub info shows up, if it does, then this is what you will need to do.

This is all based on a linksys router with default gateway of 192.168.1.1 - majority of routers have the same gateway ip.

Something to check before you get started with the steps. Make sure you are directly plugged in to the first port on your router (with your computer in 1st port) and modem connection or dsl in the one furthest to left. Go to Start>Run>CMD>ipconfig

Make sure your Local IP is 192.168.1.100 and default gateway of 192.168.1.1, if not then I am not sure these steps would apply to you as well.

Make sure you have done:
Factory Default file from USB to receiver
Sys Clean file from USB to receiver
Hard reboot (back switch)
Load 206 Bin (for elite receivers only This is June 30th fix)(if your receiver is 360p-June 30th Fix or 8000hd-June 30th Fix is the correct fix file for those receivers with this step)
Hard reboot (back switch)

First step.

1. Connect iHub to receiver

2. Leave Power on, on the receiver, but turn power off from the front panel (so that the time is displayed)

3. Connect ethernet cord to iHub, then directly in to ethernet port on computer, this part is where it is tricky and you might have to wait until you see "limited or no connectivity"

4. Open up the WIZ program, click search until it displays the fields with some sort of info. Once it does, your in luck! Now you need to skip around a little for this next step.

4 1/2. Make sure Static is checked, you should now see the fields able to change settings. Make your settings match below settings.

Local IP: 192.168.1.101 Port: 1920
Subnet: 255.255.255.0
Gateway: 192.168.1.1

Operation Mode: Mixed

Make sure USE DNS is checked!!!

DNS SERVER IP: 208.67.222.222
Domain Name: WWW.SVFTAIKS.COM

Now click on Setting, if it gives you an error after clicking, click setting again until it takes. Once it does, close the WIZ program and follow on to next step.

5. Now that you can see the iHub current info and the settings, now what you want to do is check on the back of your router, this part is crucial... Make absolute certain that your PC is plugged in to the first outgoing port on the router. And now unplug iHub from back of computer, plug it in to the 2nd outgoing port on the router (the ip that the router assigns to this port should be 192.168.1.101 by default.)

6. Open up WIZ program again, and click on Search until it finds your iHub, notice that the settings should read what I typed above? If it does then continue on, if not, then go back and retry until it does!! So now that it says the settings that we want it too, we still see the v82.0 right? Lets get rid of that now.

7. Go to Start>Run>CMD>ipconfig

Now type: ping 192.168.1.101 (if you get a series of replies, we will be able to load 1.4 with no problems at all!) Thats right, you can click thanks!!

8. Now bring the WIZ program back up, and I want you to click on Upload tab, you should be able to at this point, make sure you have extracted the 1.4 bin to your desktop. and then choose that file. You should instantly notice it start uploading with little bars with pretty much no hanging at all.

9. Once it says Completed, close WIZ, then reopen it, notice a new version?

10. Thats it, that should fix the problem

Additional steps to load bin 209 (for elite users only)This is July 11th fix for all 3 receivers(latest fix). You should see Network device connect! after rebooting receiver with iHub plugged in.

Then just put bin 209 on USB stick, upload, reboot, and you should be good to setup all your settings as before - Also, you will now be able to see your IP Config menu again and able to change settings at will.

Let me know if you get it fixed and up and running, this should fix the problems with the iHub not communicating with the receiver/not taking the files/v82 error.
__________________

[Surgeo11]

Sync45;

I would like to thank you as this method works like a charm. To see the 82 change to 1.4 in Wiznet made my day. I think the server is down now as I am still showing scrambled but my ihub is communicating. Yippee.

Thanx also to Zekester for his input.

Surgeo11

[Itaintrite]

Nice detailed tut. This will help many members I'm sure.

Best way is to check on your PC for the gateway and use that.

[Sync45]

Originally Posted by zekester

Hey Sync, I know this is a copy paste, cause i've read it somewhere before. I've highlighted in black and underlined(Factory Default file from USB to receiver) a part I have never, never heard of in the 10 yrs I've been doing this, maybe it's a typo.
See highlighted part below.
Also most peoples DNS Server IP is the same as their Gateway, just point out that the DNS SERVER IP in your thread is no where near the same as your gateway.
If this is based on a GATEWAY of 192.168.1.1 although my router assigns a 0 in place of the fist 1, why is his DNS SERVER IP different from his gateway??
Could it be his ISP giving that funky number 208.67......??
.

I don't know why those things are off, but I knew what they meant and they work great. Sorry for the trouble

[Victor Hugo]

I do not have any that kind the new box, but is good to know what is going on.
Thanks for the information to all of you guys.

[basscat02]

If you do a factory default, you are screwing it all up, WHY DO YOU NEED A FACTORY DEFAULT???? No, No, No, do not factory default

[Ralph Redan]

why do people insist on using DNS ? DNS is broken and it should not be used until svftaiks.c0m admins fix their DNS server.

[Gaspo2k]

Ok i also got mine to work but i only get a few VOD channels as opposed to a lot more PPVs whats going on is it the setup, the bin or what? I do get however all the porn channels...but whos complaining???

[Itaintrite]

Originally Posted by Gaspo2k

Ok i also got mine to work but i only get a few VOD channels as opposed to a lot more PPVs whats going on is it the setup, the bin or what? I do get however all the porn channels...but whos complaining???

None of the 500 channels are working. The 10 VODs from 5816 to 5825 (?) are working.