pantec jtag - ABA DSS

**mountaineer** · September 6th, 2005

download pantec ms repair files and extract with winzip to desktop. Take out the internet page from the folder that appears, it has the blue e on it, put that on the desktop. Click on it to show how to jtag the pantec. The files you need are added also.

sirmike_dad · September 6th, 2005

the pinout of header not same as the ms this one has 12 pins on it 2 rows x6
some have this pinout of headerr plz

jsneu · September 6th, 2005

Anyone know where the updated file is for our pantec 2500a?

jsneu · September 6th, 2005

I an searching for the new updated file, anyone have any ideas?

jubaitca · September 6th, 2005

has this worked for anyone

**mountaineer** · September 8th, 2005

I got this from another site, said it was a mx ultra.
Not fun to solder, but works like a charm.

TRST= Pin 109 ( or to R59 )
TMS = Pin 110 ( or to R52 )
TDO = Pin 111 ( must go direct on cpu pin)
TDI = Pin 112 ( or R54 )
TCK = Pin 113 ( or R53 )
GND = Connected to chasis.

mkelso2 · September 9th, 2005

I need some one to identify this receive so i can jtag it also need the jtag hook up were they go ,how to do it see pictures if they upload it has 3 buttons on the front and a serial number that starts with z0502 and ends with sx00446 it has bo jtag port inside and no flat spot that could hold a pin set up i have the jtag ready just need help in were the wires connect
Thank You
sorry no picture wont let me up load keeps timing out also someone should get the person to except paypal from canada to alabama takes a long time

mkelso2 · September 9th, 2005

Quote:

Originally Posted by mountaineer

I got this from another site, said it was a mx ultra.
Not fun to solder, but works like a charm.

TRST= Pin 109 ( or to R59 )
TMS = Pin 110 ( or to R52 )
TDO = Pin 111 ( must go direct on cpu pin)
TDI = Pin 112 ( or R54 )
TCK = Pin 113 ( or R53 )
GND = Connected to chasis.

sorr but how is this solder to the printer steel houseing like

TRST= Pin 109 ( or to R59 ) goes to what on the printer pin
TMS = Pin 110 ( or to R52 )goes to what on the printer pin
TDO = Pin 111 ( must go direct on cpu pin)goes to what on the printer pin
TDI = Pin 112 ( or R54 )goes to what on the printer pin
TCK = Pin 113 ( or R53 )goes to what on the printer pin
ned a diagram looked in you listed file
help help

bluedog · September 10th, 2005

Where the TDO goes to the cpu how many pins over from the right? By the look of the picture it is 7 pins on the cpu. can you help.

mkelso2 · September 10th, 2005

I must be the only A** hole that has this receiver or no one know anything about this i will try this again its a pantec mx ultra it was made 2004 11/06 it has a paper tag insie with ver7.30 board number is 80188p v2.0 also has 3 buttons in the middle and no ON/OFF switch in the back it has no pins inside to conect a jtag to it SO what i need it the pin setup so i can jtag this thing the board has R referance number for the transisters( NO Gs)( NO Hs) just( Rs)if some would would like to help me out with the proper pin config that would be great please dont tell about other boards or read read read i done that
Thanks

**Drockstar** · September 17th, 2005

I have the same pantec and no idea where to jtag it, help would be great. Sounds like I have a cheap nonrepairable reciever. Do I jump off of any of the pins connected to the face or power supply?

amhaz808 · September 18th, 2005

hi i get pansat 2500a but i find out that was pantec receiver can u help me how to jtag it, on the main board it said Pansat-M1007 please help and if any picture with thank you

c2321 · October 6th, 2005

I have a multistar ms which has a 16 pin connector, and a j-tag for 2500a with a 20 pin connector

is there a way to use this jtag on this receiver????
any help would be greatly appreciated....the multistar is totally dead now

**jlebron** · October 6th, 2005

Hola Perezcuco Es Mickey De Miami Mira Perdona Pero Nose Si Tu Me Contestaste El Mensaje Que Te Deje Ayer Bueno Lo Puedes Cuscar En La Lista De Convert Channel List Es El Numero 13 Ayudame Si Puedes Ok Cuidate Espero Tu Respuesta Bye Mickey

JOSEELCUBANO · October 21st, 2006

tiene incluido autoroll

solo para uso educativo saludo desde miami joseelcubano

Spacecowboy · October 8th, 2007

I have Vortex 7700 is also dead as a door nail!!! the new bin I have down loaded was a clone killer ..although it said safe....

My question is also same as the other's...I would like to know in a detailed form, how to Jtag a 2500A!!!! in my case a VORTEX 7700, which is a Pansat clone.

Every experienced member in this case, is giving us the neccesary files but never mentions ...HOW TO DO IT!!!!!

So ...if it is not a BIG PROBLEM for you, men of VISDOM, please give a detailed describtion of how to Jtag so that we the less informed MEMBERS can benefit from your KNOWLEDGE!!!

Topgun777