c/p
Originally Posted by yaesu50 View Post
FOR ENTERING KEYS MANURALY !!!!! SORRY ABOUT THE SPELLING!!!!
Ok to update you keys is very simple.. If you do this step by step you will not have a problem... But there is a problem in one thing you must get it right , if the red bar comes on it will take it out again...
{ key check: waiting for a valid key }
PLEASE TAKE YOU TIME AND READ THIS REAL WELL I HAVE DONE THIS !!! WORKS SUPER....
Ok step one.. make shore you have it updated with the last auto run in it. cw3000 8-1-07 files ECT...
Step two: go to the ADMIN and enter the pin 1111 or what ever you may have replaced it with.
Step three: go to third Party hit enter PLease..
Step four: hit enter on the word { Keys } , Please...
Step five: hi light the word in auto roll { enabled } turn it green push the down arrow key to Disabled it.
Step six: As you look at the rows, do these only !!!!!!!
0101 00 <<<< this row is keys for key86: Dishnetwork
0101 01 <<<< this row is keys for key96: Dishnetwork
0901 00 <<<< this row is keys for key86: Bell Expressvu
0901 01 <<<< this row is keys for key96: Bell Expressvu
Step Seven hi-light row exp. 0101 00 it will be white then hit the enter key and turn it green DO NOT change the no#,s 0101 or 00 go to the main row with 32 no#,s in them.****e up or down or right to left to get to each row.
Step eight After you have change it to green you will see a little line at the front of the row, move it to the end of row, { all the way right } when you are at the end far right,, but not out of sight ..
Step nine Look at your remote please ,, fine the left arrow just below the 7 key ,, called the Erase key. tap it to all the numbers are gone. It will move back to the left... Numbers Gone YES ...
Step ten You will only use the 2 and the 3 key for letters, ONLY !!!!!
All the others will be use for Numbers..[ not letters } each number 2 and 3 have 7 uses for exp. the 2 key will have the { 2 a-b-c-A-B-C } in them.. The number first then three letters in small then, three capital letters.
2 key> { 2 a-b-c A-B-C } 3 key { 3 d-e-f -D-E-F }
Step eleven Download you keys print them out and go for it. Start at the left after you remove all the old numbers. Use the key pad or remote numbers and go slowly do not use the little LETTERS. WILL NOT WORK !!! You can do a test run with the first number to get the idea how it works. By hitting the 2 number it will change 7 times. first the number then the letters. If you make a mistake DON,T Frek OUT !!!! use the ERASE key on your remote to remove you mistake.. After you put in the right letter or number it will move to the right for you by itself. Just go Slow. It will not move to the right untill you stop punching in the letter or number. try it on the first number or letter to you get the hang of it. after all the numbers are in. you are done in the first row. hit the enter key { two times please }to turn it white again so you can move it to the next row and put in the numbers..
IF YOU READ THIS RIGHT YOU SHOULD RUN THOUGH IT LIKE A BABY..
If you have a problem.. let me know I will check this from time to time to help... This should be posted all the time for all to enjoy....
GOD BLESS From yaesu50 and micro69 .
:
This part will Tell you How to Turn the auto OFF PLEASE do this First !!!
Now read this very carefully,,, I got this As well.. I will not take credit for the work but here it is.
GORDO Want to thank for this work...
C&P
Press Menu, then System Setting, then OSD, go to the bottom menu option and turn off Auto Roll
Press exit key twice, you'll see main menu again
Press Accessories, Key Menu, press left arrow key one time, you'll see Nagra2 at the top of the screen
Press down arrow key 5 times, you'll see The "Provider of choice" as the provider name at the far right of the screen, and there are two keys, one identified as position 5 at the far left of the screen, the other positioned as 6 right below.
The key in position 5 should be highlighted in blue.
Press the green button marked as ZOOM on your remote control. For some reason, the programmers allow you to change the provider ID and Index numbers, and there's no need to change those. Press the right arrow key until you're on the first digit under the title "KEY". Then enter the following:
Latest keys of your choice
Mistakes can be edited with the back arrow key. Once you've got all of the first key entered and you're sure it's correct, DO NOT press the exit key. Instead, press the down arrow button until the OK is highlighted and then hit the OK button. That will save the Key. Now hit the down arrow key once, so that the key beside position 6 (which should also be listed as provider name XXX) is highlighted in blue. Press the green key, and repeat key entry with the following:
Latest Keys of your choice
This may not work on your system ok...But it will work on some....
POSTED BY
hereandthere
and GREAT HELP IT IS TO...THANKS hereandthere
Press the Menu button then navigate as follows:
6 System...
1 System Setup
1 VDR-Installation...
9 Plugins-Setup...
1 sc
Turn "Update Keys (AU): to off.
I have done this to get it to work,,if you want to mannel put your keys in do this to the letter,,
now check this first, go to Admin screen first, go to updates, hit enter please go down to system and hit enter please...If you have Captive works 1.0.1.9 next roll Sc .0.6.2.08.01 you are in good shape..
Go to menu under any profile, example . USER go to any open Channel ,, press in this order
menu 6,{system} 1,{system-setup} 1,{VDR-Installation] 9,{Plugins-Setup} 1{SC }.. ok in that order now it will say sc {0.6.2 } - A software emulated cam. Number may be different..
hit enter on that one only !!!! do NOT TOUCH ANY OTHER ONE OK IT will come up and say
UPDATE KEYS {AU} <ACTIVE CAIDs> USE YOUR RIGHT ARROW ON YOUR REMOTE AND TURN IT OFF
REboot system . then you can enter the keys in the instrustion that I put on here !!!..
PLUS BEV sends keys ever so offen not like DN you must wait for it to update all the time. PLUS I leave It on BEV so it is updated all the time, I move to DN for other moves at time...
I hope this helps you out on this ...
Linear Mode
