ABA DSS - Free to Air Satellite TV Community - View Single Post

**carpenter1** · November 11th, 2006

Instructions on Loading the New OSD bins on a Captive Works s600

1st Release-CX_KroundV1.06_24138Chip.bin

This is the CX-Kround V1.06 new OSD bin for Captive Works 600S summer main board.. It is recommended to load the Captive Works Factory file before loading this New OSD bin. DO NOT load the new OSD file on anything other the a Captive Works 600S!!

If you try loading this New OSD file on a Skyview Rx600 it may damage your receiver and you have been warned!

1. Power off the receiver from the back switch.
2. Hold the front panel power button and while holding turn on the back switch, your receiver should display (boot)
3. Load the CX_KroundV1.06_24138Chip.bin using the old Upgrade1.04V loader.
4. When finished your receiver will display END, power off and on the receiver
5. Put receiver into standby mode by pressing the front panel power or remote power, your receiver will display (--:--)
6. Use the UpgradeV1.05 Loader to load the CX-LoaderV2.50.bin
7. If you do not upload the CX-LoaderV2.50.bin you can not watch the patch channels...

NOTE: If you have the kround software in your receiver from now on you must use the V1.05 tool to update your software and you CAN NOT go back to the old Summer Version Files.

Please make sure when you upload the files, make sure the power is always on. If you shut down the power while its loading, it will damage the receiver.

2nd Release-CX_Kround V1.07US.bin

Please load this file like before using V1.05 loader if your receiver is already updated to the new OSD CX_KroundV1.06_24138Chip.bin. If not, you need to update your receiver from the 1st release (CX_KroundV1.06_24138Chip.bin) and then load this file (CX Kround V1.07US.bin)

1. Power off the receiver from the back switch.
2. Hold the front panel power button and while holding turn on the back switch, your receiver should display (boot)
3. Load the CX Kround V1.07US.bin using the NEW Upgrade1.05V loader.
4. When finished your receiver will display END, power off and on the receiver
5. Put receiver into standby mode by pressing the front panel power or remote power, your receiver will display (--:--)
6. Use the UpgradeV1.05 Loader to load the Dish Channel list For Kround bin.
7. Choose Download S/W option like you do for the bin file and then select the Dish channel list for Kround.bin and click start!
8. The channel bin will load much faster, DO NOT Interrupt, your receiver will display END when done!

- After Loading the Dish Channel list For Kround bin the option for "Dishnet Full Name" will work.

- Please DO NOT try to download the old software channel list to the new one because it’s two different software programs and are structured different. There will be a new updated channel master program for the new OSD

3rd Release-CX_Kround V1.08

You can skip the 2nd Release CX-Kround V1.07bin. Make sure you load the 1st Release CX-Kround V1.06 then this 3rd Release CX-Kround V1.08!!

-After you put the 1.08 bin file, you can load the Dish Channel list for Kround. Bin, just like you load the bin file. You don’t need to load the dish full name file if you have already loaded it before.

1. Power off the receiver from the back switch.
2. Hold the front panel power button and while holding turn on the back switch, your receiver should display (boot)
3. Load the CX Kround V1.08.bin using the NEW Upgrade1.05V loader.
4. When finished your receiver will display END, power off and on the receiver
5. Put receiver into standby mode by pressing the front panel power or remote power, your receiver will display (--:--)
6. Use the UpgradeV1.05 Loader to load the Dish Channel list For Kround bin.
7. Choose Download S/W option like you do for the bin file and then select the Dish channel list for Kround.bin and click start!
8. The channel bin will load much faster, DO NOT Interrupt, your receiver will display END when done!

4th Release-Captive Works Bell Channel list Kround bin

You can Load this file on top of your Kround software (any version of the Kround OSD) to get the bell full channel name.

1. Open update tool V1.05 Loader
2. Put a check in Download S/W (like you use for regular file downloading)
3. Click on the file in top right corner and Select this file
4. Click Start to download it to your receiver
5. This file will load fast and DO Not interrupt!
6. Your Receiver will display END, no need reboot your receiver

Now Press Menu>>System Setting>>System>> and Turn your bell & dishnet full Name option to "on". If you loaded both BEV & DN channel files then you will now have Full channel names for both!!

Good Luck and I will update this manual when needed!

November 11th, 2006	#2 (permalink)
carpenter1 Super Moderator Join Date: Jan 2005 Location: On the computer Posts: 6,225 Credits: 7,911.00 Thanks: 303 Thanked 2,591 Times in 914 Posts	Step's to load the New OSD files!! Instructions on Loading the New OSD bins on a Captive Works s600 1st Release-CX_KroundV1.06_24138Chip.bin This is the CX-Kround V1.06 new OSD bin for Captive Works 600S summer main board.. It is recommended to load the Captive Works Factory file before loading this New OSD bin. DO NOT load the new OSD file on anything other the a Captive Works 600S!! If you try loading this New OSD file on a Skyview Rx600 it may damage your receiver and you have been warned! 1. Power off the receiver from the back switch. 2. Hold the front panel power button and while holding turn on the back switch, your receiver should display (boot) 3. Load the CX_KroundV1.06_24138Chip.bin using the old Upgrade1.04V loader. 4. When finished your receiver will display END, power off and on the receiver 5. Put receiver into standby mode by pressing the front panel power or remote power, your receiver will display (--:--) 6. Use the UpgradeV1.05 Loader to load the CX-LoaderV2.50.bin 7. If you do not upload the CX-LoaderV2.50.bin you can not watch the patch channels... NOTE: If you have the kround software in your receiver from now on you must use the V1.05 tool to update your software and you CAN NOT go back to the old Summer Version Files. Please make sure when you upload the files, make sure the power is always on. If you shut down the power while its loading, it will damage the receiver. 2nd Release-CX_Kround V1.07US.bin Please load this file like before using V1.05 loader if your receiver is already updated to the new OSD CX_KroundV1.06_24138Chip.bin. If not, you need to update your receiver from the 1st release (CX_KroundV1.06_24138Chip.bin) and then load this file (CX Kround V1.07US.bin) 1. Power off the receiver from the back switch. 2. Hold the front panel power button and while holding turn on the back switch, your receiver should display (boot) 3. Load the CX Kround V1.07US.bin using the NEW Upgrade1.05V loader. 4. When finished your receiver will display END, power off and on the receiver 5. Put receiver into standby mode by pressing the front panel power or remote power, your receiver will display (--:--) 6. Use the UpgradeV1.05 Loader to load the Dish Channel list For Kround bin. 7. Choose Download S/W option like you do for the bin file and then select the Dish channel list for Kround.bin and click start! 8. The channel bin will load much faster, DO NOT Interrupt, your receiver will display END when done! - After Loading the Dish Channel list For Kround bin the option for "Dishnet Full Name" will work. - Please DO NOT try to download the old software channel list to the new one because it’s two different software programs and are structured different. There will be a new updated channel master program for the new OSD 3rd Release-CX_Kround V1.08 You can skip the 2nd Release CX-Kround V1.07bin. Make sure you load the 1st Release CX-Kround V1.06 then this 3rd Release CX-Kround V1.08!! -After you put the 1.08 bin file, you can load the Dish Channel list for Kround. Bin, just like you load the bin file. You don’t need to load the dish full name file if you have already loaded it before. 1. Power off the receiver from the back switch. 2. Hold the front panel power button and while holding turn on the back switch, your receiver should display (boot) 3. Load the CX Kround V1.08.bin using the NEW Upgrade1.05V loader. 4. When finished your receiver will display END, power off and on the receiver 5. Put receiver into standby mode by pressing the front panel power or remote power, your receiver will display (--:--) 6. Use the UpgradeV1.05 Loader to load the Dish Channel list For Kround bin. 7. Choose Download S/W option like you do for the bin file and then select the Dish channel list for Kround.bin and click start! 8. The channel bin will load much faster, DO NOT Interrupt, your receiver will display END when done! 4th Release-Captive Works Bell Channel list Kround bin You can Load this file on top of your Kround software (any version of the Kround OSD) to get the bell full channel name. 1. Open update tool V1.05 Loader 2. Put a check in Download S/W (like you use for regular file downloading) 3. Click on the file in top right corner and Select this file 4. Click Start to download it to your receiver 5. This file will load fast and DO Not interrupt! 6. Your Receiver will display END, no need reboot your receiver Now Press Menu>>System Setting>>System>> and Turn your bell & dishnet full Name option to "on". If you loaded both BEV & DN channel files then you will now have Full channel names for both!! Good Luck and I will update this manual when needed!