Latest fix no signal

[Tony F]

I downloaded the latest fix and get no signal on all channels. have hard booted, no signal.

Please help.

[tomcat01]

check the connection if you have no signal something is not hooked up properly push in the sat cable etc...

[reilly2106]

it the cannels with no signal on same ssatellite or diffrent

[Tony F]

checked everything, all is ok.

[Mighty Thor]

Originally Posted by Tony F

checked everything, all is ok.

connection ok ..... still no sig OR all is GOOD Now

[Tony F]

Originally Posted by reilly2106

it the cannels with no signal on same ssatellite or diffrent

same satellite. i tried channel up and down, still no signal

[Tony F]

Originally Posted by Mighty Thor

connection ok ..... still no sig OR all is GOOD Now

connection ok, still no signal

[Mighty Thor]

make sure your bin loaded properly? If still nothing, shut down, disconnect all & unplug unit leave down for 10 - 20 min reconnect all & plug back in and turn back on.

good luck & Let us know...

[TDuke]

Do a factory reset. Load the clear file then load the new bin. Reboot between each and everything should be good.

[Tony F]

Originally Posted by TDuke

Do a factory reset. Load the clear file then load the new bin. Reboot between each and everything should be good.

how do i do a factory reset? do i just load the factory file and the clean file found in the download section?

[TDuke]

Originally Posted by Tony F

how do i do a factory reset? do i just load the factory file and the clean file found in the download section?

Menu/advance/reset factory default. If you have not done one of these before make sure you write down your antenna settings before you do it. You will have to reset them once it's done. Also, once you put in the newest bin, you will need to rescan for channels.

Hope this helps.

[tomcat01]

sorry bud the connection is not ok the reason i say this is the reciever sends a signal to the lnb it has nothing to do with the bin .. if you want to put on a factory file and you still will not have a signal ..

if you also do not believe me take your lnb off shut off the back of the reciever and hook up a 4 foot cable and stand there with the lnb in your hand and if the CABLE IS GOOD then you will see a signal if you really want to waste your time factory reseting and scanning and all that go ahead

but first you need a proper connection or you could be there for years ..

[TDuke]

Let us know what you find out. I'm very interested in the solution to your problem.

[Tony F]

Originally Posted by TDuke

Let us know what you find out. I'm very interested in the solution to your problem.

I did not do a factory reset. i rescanned the channels and only receive some channels now. i have both 110 and 119 but for some reason i am not getting all of the channels.

Can you tell me what the correct settings are for 110/119?

thank you

[Tony F]

These are my current settings:

Satellite

[Tony F]

These are my current settings:

Sat 119.0 W Echostar 7
Transponder 12239H 20000 Auto
LNB Power 13/18V
LNB Type OCS-DP
LNB Frequency 11250
22khz Off
Switch Type Off
Option Off
Legacy SW SW21 Dish 1

[creativegenius]

For 110
Your ANT settings will look like this:

LNB type - OCS-DP
LNB freq - 11250
22khz - off
LNB power - on
transponder - 12224
search option - all
network search - on
disqec - port 2 (or whatever port matches your the wiring to switch)
motor -off
legacy switch -off


For 119,
Your ANT settings will look like this:

LNB type - OCS-DP
LNB freq - 11250
22khz - off
LNB power - on
transponder - 12239
search option - all
network search - on
disqec - port 1 (or whatever port matches your the wiring to switch)
motor -off
legacy switch -off

Creative Genius

[Tony F]

Originally Posted by creativegenius

For 110
Your ANT settings will look like this:

LNB type - OCS-DP
LNB freq - 11250
22khz - off
LNB power - on
transponder - 12224
search option - all
network search - on
disqec - port 2 (or whatever port matches your the wiring to switch)
motor -off
legacy switch -off
For 119,
Your ANT settings will look like this:

LNB type - OCS-DP
LNB freq - 11250
22khz - off
LNB power - on
transponder - 12239
search option - all
network search - on
disqec - port 1 (or whatever port matches your the wiring to switch)
motor -off
legacy switch -off

Creative Genius

Thanks, my settings are pretty much the same but i don't have some of the options you mention above, such as search option, network search, disqec and motor. Does this have something to do with the lastest news re: international channels?

[TDuke]

My system did the exact same thing when I changed to the newest bin. I did a factory reset, loaded the clear file, loaded the new bin again rescan all was fixed.

[Tony F]

Originally Posted by TDuke

My system did the exact same thing when I changed to the newest bin. I did a factory reset, loaded the clear file, loaded the new bin again rescan all was fixed.

I did the factory reset, loaded the latest bin and re-scanned the channels but still do not get all channels. ie. Spike, Nickelodeon, etc. There are a lot of channels with no information.

How do I load the clear file? Or will it help me in this situation?