CW800 Remote Control - ABA DSS

Bokchoy · May 12th, 2009

Hi all,

Need some help with my CW800 remote control. I think my kids has broken the remote and its now not working at all. Any recommendations?

Thanks for your help on this matter.

Bokchoy

**snakebite** · May 12th, 2009

you could try putting factory file then bin again ,i have had to do this with my 800.

**ccelectro** · May 12th, 2009

This might seem a little bit out of the ordinary, but if your kids play with the remote, check and see if the batteries are in correctly. [just a thing with the kids].

**snakebite** · May 12th, 2009

i lost the use of my remote and it would not respond to anything.i had to load everything through the menu buttons on the front,once factory file was in it came back just like that.it could aslso be a loose wire in the remote ,these are not the best made.

**mountaineer** · May 12th, 2009

Make sure the stb button on the remote is pushed.

**VGiddy** · May 12th, 2009

If the remote is dropped several times the the infra red does not work and the remote is rendered useless.
If you go to an authorized dealer they will sell you a remote for it.

chas6622 · May 12th, 2009

They have them on ebay for around 20.00

**boboisno1** · May 12th, 2009

Click on the ink below and see if it helps any.

http://www.abadss.com/forum/807-cw-8...emote-fix.html

Bokchoy · May 13th, 2009

Hi All,

Thank you all for the wonder replies. I think the remote is gone!! It won't even remote my television.

Bokchoy

**mountaineer** · May 13th, 2009

They are made kind of cheap.

thoger · May 13th, 2009

disculpa no se si ya checaste si no se quedo trabado algun boton, hay ocaciones que por estar presionado alguno de ellos el control no funciona,te recomiendo que presiones boton por boton para ver si se destraba, el control no debe de emitir luz a menos que presiones algun boton checa que el control no tenga luces encendidas si emite luz es señal que esta trabado

thoger · May 13th, 2009

Una manera de detectar que el control ya no funciona es poner en un radio de AM seleccionas donde no haya estaciones de radio, acercas el control y al presionar cualquier tecla de el control se debe de escuchar un sonido muy peculiar y pulsante. si no emite ese sonido tu control ya se daño y requiere reparacion o cambio

**creativegenius** · May 13th, 2009

Try pressing the 'STB' button on your remote First.

Creative Genius

alex1967 · August 17th, 2009

how can i reprogamed my remote for a new tv?

**creativegenius** · August 17th, 2009

Here you go dude:

Captiveworks CW-800S PVR How To Program Remote Device

Code input

1. Turn on the device which you planning to program

2. Find the code from the code list to match the brand of your device.

3. Press "SET" button until 3 seconds later, then LED will be light on.

4. Press the device function button( ex. TV), then the LED will light once.

5. Input the 3 digi code which matches the device in the list, the LED will blink once for each code. If the code is valid for this device, the LED will be off, means the code is fit for this device. If the code is not valid, the LED will be off after blink some times, means the code is not correct for this device, need to input new code.

6. Now to test whether the RCU can control the device, if can't, return back to the code setup procedure, and input other code that supposed to match this brand device, if all the code under this brand can't control this device, you need to try the following way by code searching, you may be able to find the code.

7. Write down the correct code for next time use.

Manual code search

Code searching means starting from the current device by pulsing 1 to continue search, one time "POWER" one time plus 1 to the code.

1. Press "SET" and hold it for 3 seconds, then LED will be light.

2. Press the function button (ex.TV) , LED will blink once

3. Aim the RCU to the device (ex. TV) and press "POWER" button, one time "POWER" you will get LED blink once.

4. When it switch off the device, means the code you input is correct, then press"EXIT" and save the code, LED will be off. If you have problems with tv and dvd hold SET down for 3 seconds while holding SET push TV or DVD while SET is being pushed. Led light on TV or DVD should stay on, then put code in.

Code auto setup

1. Press"SET" and hold for 3 seconds, LED will be on

2. Press the function button(ex.TV), LED will blink once.

3. Aim the RCU to the device (ex.TV) and press"POWER" button once and release.

4. When it switch off the device, means the code you input is correct, then press"EXIT" and save the code, LED will be off.

Code Display Setup

1. Press "SET" and hold for 3 seconds, LED will be on,
release the button.

2. Press the function button (ex. TV), LED will blink once.

3. Press "SET" button again, LED will blink once.

4. Press any numeric button, when you press one number and make the LED blink once, this number should be the first one in the code.

5. Repeat the above 4, take the same way to find the second and third number for this code.

When you find the third number, the LED will be off

Creative Genius

dirtywill2001 · August 17th, 2009

the manuals that come with the stb's are almost useless but this is one of the things that is included in the manual...right b-4 the remote codes you will need.