Nfusion tp 12239 - ABA DSS

Jim Warren · 2 Weeks Ago

HI

I am missing 204, & 205 among others.
I noticed the tp for 119 is pre-set to tp12457,
if I change it to 12239 and rescan will I pu the missing channels?

Nfusion HD

Thanks

**SatelliteJunkie** · 2 Weeks Ago

Quote:

Originally Posted by Jim Warren

HI

I am missing 204, & 205 among others.
I noticed the tp for 119 is pre-set to tp12457,
if I change it to 12239 and rescan will I pu the missing channels?

Nfusion HD

Thanks

12239 is the freq for 119.
12224 is the freq for 110.
You may need to do a reset to remove old channels prior to rescan, or you may get duplicate channels.

Jim Warren · 2 Weeks Ago

Hi

NO dups or 204,205

Can you help???

Thanks

**SatelliteJunkie** · 2 Weeks Ago

Plenty of nF testers here...but I'm not one of them.
Better help is on the way, but did you try to rescan?

**buddyjh** · 2 Weeks Ago

Do what SJ suggested and rescan 110 using transponder 12224 and 119 using 12239 and lnb freq 11250...both of those channels are on 119 and TP 12239 so you might just wanna rescan 119...don't know what kinda weather you're having where you are but that could be an issue when you're scanning for channels.

**snakebite** · 2 Weeks Ago

what are you getting for s/q on 119?have you checked to see what your getting for that peticular tp?

Jim Warren · 2 Weeks Ago

Quote:

Originally Posted by snakebite

what are you getting for s/q on 119?have you checked to see what your getting for that peticular tp?

Hi

Thanks for responding.

119 S=87 q=99
110 s=83 q=99

I had this trouble using my SV360 Elite and SV8000 until I changed the lnb's to DP OCS.

I'm using a new 1000.2 with 3 combined LNB's and 1 cable.
This one has lnb settings for standard, Universal. Legacy twin lnb1, Legacy twin lnb2, Legacy quad lnb1, Legacy quad lnb2, DPLNBF. It defaults to standard.

Can you help??

Thanks

GUESS WHAT I JUST USED DPLNBF AND I GOT THE CHANNELS!!!.
I DID NOT FAC RESET, BUT NO DUPS

**snakebite** · 2 Weeks Ago

Identifying Marks
-----------------
Uniquely shaped LNB
DishPro Plus markings
3 coax connector outputs and one coax input.

Usage
-----
These are used to provide signal from 3 (or 4) satellites to up to 3 receivers (specifically 129/119/110).
Using DPP44 switches you can feed many more receivers. When using DPP44s the input port is disabled and you will need to connect the LNB directly to the DPP44.
DishPro Plus (DPP) LNBs are power hogs and some FTA receivers may have trouble powering it by themselves without power inserters or a sub box hooked up too.

Antenna Settings
----------------
LNB Type: Single DPLNBF
LO_freq: 11250
Sat 1: DiSEqC 1.0 Port 1
Sat 2: DiSEqC 1.0 Port 2
Sat 3: DiSEqC 1.0 Port 3
Sat 4 (input port): DiSEqC 1.0 Port 4

this is the settings i found for this lnb.hope it helps.

**snakebite** · 2 Weeks Ago

do you run these lnbs through a dp44 switch or not? the lnbs you have are 3 together ,made for 110-119-129?

**zekester** · 2 Weeks Ago

I wouldn't worry about the TP being preset at 12457, when you scan it will still pull in the channels associated with 12239, at least mine did. Haven't had any missing or dups with this mighty Solaris,

**snakebite** · 2 Weeks Ago

you lock on tp say 12239 it is in there but it will default to the same tp everytime you look.hope this makes sence to you.

Jim Warren · 2 Weeks Ago

Quote:

Originally Posted by snakebite

do you run these lnbs through a dp44 switch or not? --------NO
the lnbs you have are 3 together ,made for 110-119-129? -- YES

It came with the switch but the installer said it was'nt needed.

Thanks

**snakebite** · 2 Weeks Ago

ok thanks and you are all fixed up now.thanks for the feed back.