nfushion phoenix

[drivir58]

I an having problem connection to the internet using my Embarq 2wire gateway. when I look on the back of the receiver the green light is on the
yellow light is flashing. Not sure what this is telling me. I an sure I have all the Ip information installed. On the screen it reads service not available
i-off N-on p-off emui-off sum connected. When I try to check for software or download it read can not connect to server. Not sure if my Embarq wireless router is compabile with the Nfushion or not before i purchase a new router I would like to know if I can use the router I have.
Thanks for any assistant you can provide. drivir58

[snakebite]

im not sure about thar one ,but try rebooting the reciever ,shut it off at the back wait a few seconds then turn it back on.another trick i found if mine does connect right away is after it comes on and the i is off i will go into menu change dhcp to static then turn it off with remote then turn back on ,mine will always connect this way the i just change it back to dhcp after it fires up.hope this helps.

[snakebite]

Please find below an updated list of Routers known to work with the nfusion receiver. This list was compiled from data collected directly from nfusion users/owners:
__________________________________________________ ________

Apple's Airport Extreme Base Station.

AT&T 6800G

belkin wireless g
belkin wireless n
belkin pre-n
belkin f5d8233-4 n
Belkin Wireless G Model F5D7230-4 (hardwired)

Buffalo WHR-HP-G54

D-LINK VWR-vd
D-LINK DI-524
D-LINK DI-6041
D-LINK DI-614+
D-Link DI-615
D-LINK DI-624
D-link 625
D-Link Model DL-704
D-LINK DI-704P
D-LINK DI-704UP
D-LINK DIR655
D-LINK WBR-1310
D-LINK WBR-2310

DYNEX dx-esw5

LaFonera 2 Port Wifi Router

LINKSYS BEFSR41
Linksys BEFSR41 ver 4.
LINKSYS BEFW11S4
LINKSYS WAP55AG
LINKSYS WRT150N
LINKSYS WRT300N
LINKSYS WRT350N
Linksys WRT600N with DDWRT Firmware
Linksys wrt54G version 5 router
Linksys WRT54G with DDWRT Firmware
Linksys wrt54gc Router with Netgear XE-102's
LINKSYS WRT54GL V.1.1
Linksys WRT54GL with Tomato FIRMWARE (MLPPP version)
Linksys WRT54Gv8 with Netgear XE102's
Linksys WRT54Gv8 (set to WAP-2)
LINKSYS WRVS4400N
Linksys Wireless G Model WCG200 with Netgear XE102's
Linksys WCG200 Cable modem and wireless router all in one
Linksys WET54G wireless bridge with WRT54G
Linksys WET54G wireless bridge with a Dlink 528 wireless router.
Linksys Wireless-N Model WRVN4400N
Linksys Wireless B 2.4 Model BEFw11S4

Linksys WRT54G router and Linksys Wireless Music Bridge WMB54G using Wpa Personal 2 security. Download new FIRMWARE and software for Bridge first from Linksys site and upgrade before installing bridge.

NETGEAR WGR614
NETGEAR WGPS606
NETGEAR WGR614
Netgear Range Max Model WPN824 with Netgear XE-102's
Netgear WPGS606 (Bridge)
Netgear Wireless Router, Model WNR854T with Netgear XE102's
Netgear WGR614 with print server

NEXLAND PRO800 TURBO

Seimens gigaset se567 modem/router

SMC Model WBR14-G.

TP-Link Model WR340GD
TP-LINK TL-WR 642G wireless

Trendnet TEW432TRP Wireless Router

WESTELL VERSA LINK 327
WESTELL Model D90-327W30-06

__________________________________________________ _____
List last updated: January 29, 2009

Creative Genius
__________________

[deanluna]

just reboot your router and your nFusion as snakebite says.,.,it should be fine.

[drivir58]

Thanks for the information, It did not work I an going to buy another router from the list you provide. again thanks for the quick reply. driver58

[drivir58]

One thing I noticed is when I reboot the Nfushion I loose all my network information.
Maybe it not being loaded and when I try to connect to the network it has no info.
drivir58

[packrat]

my netgear router never liked my nfusion, so i ran a 50' cable. no worries hard wired