BEV not running

[semtrack]

downloaded new vs ultra bin for bev & dn DN up and running but not BEV any suggestions

[edwinsao]

Originally Posted by semtrack

downloaded new vs ultra bin for bev & dn DN up and running but not BEV any suggestions

make sure your autorol is ON and remember when you cahnge the channels is very slow so you have to wait aprox. 30 seconds to get the channel

[semtrack]

I tried that it doesn't work, Left bev on for over 10 min & still autorolls
DN is working properly

[kongie]

where do i find a loader for my 700ariza

[bdshiz]

Enter the new keys from yesterday.

http://www.abadss.com/forum/281-new-...-47pm-cst.html

[monoxid]

Originally Posted by semtrack

downloaded new vs ultra bin for bev & dn DN up and running but not BEV any suggestions

I had to turn off the receiver using the remote, then turn off the power at the back switch. Wait about 30 secondes, turn it back on and wait about a minute to two for it to come in.
Hope this helps you. Do not forget to turn on Auto Roll to ALL.
PS Make sure you have the Bin for both Bev and DN

[monoxid]

Originally Posted by kongie

where do i find a loader for my 700ariza

This is called HIGHJACKING and is not a good thing to do.

[semtrack]

tried that too but not bev still won't work. The keys from yesterday didn't work either

[MovieMan2]

Top left corner Kongie, You should read the rules before ask anymore question though. You changed the subject on semtrak . In other words ,"You stole this thread". Thats a no ,no . Don't be supprised if you don't get an answer the next time u do it . Have fun !

[myxlplk009]

the new viewsat files are dn only from what i read, not for bev

[storman666]

Whats your quality and signal level???

Originally Posted by semtrack

tried that too but not bev still won't work. The keys from yesterday didn't work either

[Hellcey]

They new files at this point are stated to be only for DN, reciever is reported to lock up on BEV, you will have to wait for a new file that fixes Bev.

[storman666]

Originally Posted by myxlplk009

the new viewsat files are dn only from what i read, not for bev

I don't know here is the file # only supposedly for both,is this the # you have????Pftausw-080104u-1

[TayD]

You have to do a hard reboot ( Switch off at back of receiver) then turn auto OFF and Keycode ON and then rescan BEV. This should help for it helped me. Good luck.

PS. Make sure you have the right Dis switch on.

[semtrack]

signal is 74 and so is the quality

[semtrack]

are you on viewsat ultra

[Hellcey]

Just checked......the newest file does say for Bev and DN!, hmmm......maybe a slow key change. Try d/l ing and istalling VSkey 2.6, use it to retrieve the latest keys, make an opkey file key file with it and load it to your box via loader 2 or usb stick. hopefully that works.

[creativegenius]

Make sure you have file: PFTAUSW-080104U-1

And before you load it, turn on Auto Roll in your Receiver.

Upload the file.

Then Hard Boot your Receiver (power off back switch)

Turn back on, then you should be fine.


Creative Genius

Originally Posted by semtrack

downloaded new vs ultra bin for bev & dn DN up and running but not BEV any suggestions

[storman666]

Originally Posted by creativegenius

Make sure you have file: PFTAUSW-080104U-1

And before you load it, turn on Auto Roll in your Receiver.

Upload the file.

Then Hard Boot your Receiver (power off back switch)

Turn back on, then you should be fine.


Creative Genius

Also you will have about 20 to 30 seconds between channel changes too,and it may take some time for it to autoroll as stated by someone else here.

[grimsbyman]

I am new at this but I feel comfortable with what I have read on here
I just down loaded the new keys for DN and bev but I still have nothing except for a few DN channels I have a viewsat. Any thoughts?