Got 253 & 1.9 loaded yesterday & it worked for a little while & froze,
When I reboot it works for a few minutes on ch 105 & freezes,
Tried reloading 245 & 1.4 SW & it works fine, Just limited channels,
Upgraded to 253 & 1.9 again & same thing, works a few minutes &
locks up, Help...

Installed new i-hub file and new bin........worked fine for an hour or so........nothing since..been 2 days....any ideas ?

I need 1118W channel list, that i can load in my cnx nano2 reveiver.
Thanks

is any one else freeing every 2 seconds--- how do you fix it:bowl:

I have two dishes, one Nimiq 1,3 and one Echostar 3. The Echostar is the one that gets me DN and its pointing to 91.0 W. Is there any way I can get DN using my ihub without moving my dish to face 110 or 119. Simple question. Yes or No. People have been telling me it works on 110, I know that but that doesn't answer my question...do I have to move my satellite to face 110 or can I scan Echostar 7 that says 110 and be done with it? Confussed and need a simple straight forward answer. Can I get DN using my Echostar 3 (91.0 W) using the new bins on ihub??

Is bev up on the sv premier as much as I hate to I have to go back to something i'm use to working at, the cnx is great but causing me some problems, won't recognize bev at all but got it hook up in the same room as the nf and the nf will pick bev up but cnx won't, don't make sense.

Does IHub 1.9 give us better testing in terms of PPVs or channels?

Uploading v250 - do we need to disconnect IHub from the Premier unit? Think Tomcat said that (I could hear it wrong)?

thx

I am testing the 360E and 360P. Update on the Elite went fine. I have Wiznet 1.9 and have updated the P to SV360Premier_v0250. I have done a hard reboot and re-scanned. I am getting nothing. I can see ch100 fine but not 200 (or others).

Any suggestions will be appreciated.

Why is it when I save and exit from wiznet, and open it again, my setting are gone, but the Prem still works?

since june, i have bought a second sonicview premier and 2 ihubs. i have never been able to get any channels. i did get and occasional connect message but never any picture. today i downloaded the 1.9 and 250 from the sonicview site. the only way i could get the wiznet to work was to connect my computer directly to the hub. during the first 45 seconds when the yellow light was blinking, i was able to connect with wiznet and upload 1.9. i turned the sonicview off and on with the switch on the back, and quickly accessed wiznet again. server ip was gone, and the port was 9999.
i quickly changed to 77.93.75.89, and 1920, clicked settings, rebooted the sonicview. for the first time ever the screen came up with connecting message and 5 seconds later i have 105. ive checked other channels and everything is working fine. thank you sonicview!!!

ok guys i just about gave up before so i havent been on in a while looks like they might have something working so what do i need to do first to try and get back up i have the i hub does it still need to be hooked up to pc and also i have vista it was so complicated before i just stopped tryin any help would be thankful...

C/P
.
Part 1
1) if your system was using DNS=YES and it works then goto "part 2"
2) Make sure your system works before proceeding.. Check USA (105)
3) Open your IPCONFIG and change to DNS=YES. Confirm Domain is correct, confirm ports, Once you have made sure all is correct check for picture.. if it works continue..if not.. reset router.. reset receiver..check again..
Part 2.
1) Load the new file on the receiver.
2) Open the Wiznet program.
3) Click Search.
4) make sure all the info is as shown below.. ( note: Your IP and Gateway will be different numbers but the same points shown below apply.) all the rest should be as shown in the picture below
5) Once you confirm the settings are correct.. Click "Setting"
6) Click Upload
7) Choose 1.9 (UNZIPPED) file. It will load. Close Wiznet.
8) Open Wiznet... Click "Search"
9) Confirm the Version is 1.9 and all settings are correct.. If anything has changed in settings... leave it alone for the moment and proceed.
10) Turn Receiver off..then On from rear switch.. Check for picture on USA (105). If it works... Close Wiznet..
11) If it didn't work.. Go back to Wiznet and repeat steps 4 and 5.
12) turn off receiver.. Reset router via the web interface. After the router completes its reboot..turn on receiver and look for connected message.
ONCE YOU GET IT WORKING LEAVE IT ALONE... DON'T OPEN WIZNET AGAIN.

After upgrading ihub to 1.9 and loading new bin all channels still scrambled, unit went dead while looking at ip config, black out no video/audio only a single letter across the display, any idea's?????

Have loaded reloaded cleaned out stb & ihub,
Reloaded wiznet, Tried all new files Dhcp & Static,Still nothing with rom250
on stb & 1.9 on wiznet, I can reload 1.4 & 245 files & It's working,
3 days & nothing except a few open,100 etc channels with new SW,
Help!

if any 1 is having problem try this:

Download the new files extract them to your satellite files folder.

Two files one for wiznet (1.9) and receiver too
Load the receiver file to the flash drive. 2.50 for premiere, 219 for elite and 207 for hd

Open wiznet
hit search
Hit upload
Load version 1.9
save settings
Exit wiznet
reopen wiznet 1.9 should show as version number
Open usb window in receiver
Scroll down and install new receiver file using s/w update
Open ip config in receiver
Set dhcp
add serial number
hit apply
reboot
that should be it
it ll take a few minutes to picture time but it rocks
you can also debrick an 82 version as well